KEYS850JQ1 KitchenAid Dryer - Instructions

Remove Filter and (2) phillip screws. Use common screw driver to pry top from cabinet. Fold top back. disconnect door switch and removed (2) screws holding front of cabinet and lift frong slightly to remove from cabinet. Remove broken belt and discard. check rollers for freedom and placed drum on rollers. guided belt through idler and around motor pulley. lift front and placed on lower hooks. Lift drum and installed (2) screws that holds front of cabinet to main cabinet. connect door switch and check drum for freedom of turn. turn drum several times to get belt to center. Closed top and replaced (2) screws that hold filter door in place. Install filter and test run dryer. Completed job in about 38 minutes.

I followed the instructions supplied with the belt. I've changed the belt before so was familiar with the repair. The toe panel clips for my model had changed so what was supplied was different than the originals. Although they, too, came with instructions, they did not fit my appliance. They were inexpensive so I scrapped them and used some self-adhesive Velcro fasteners I had in a junk box.

I replaced the Cycling thermostat. At first I thought I may have blamed the wrong part because the ohm meter read almost the same for the old and the new part. It took less than a day for the part to come probably because it came from Jacksonville. I haven't guessed how much I saved by not calling a appliance repair.

belt # 346995. part was delivered quickly. Part fit perfect, no problem. there was a video on youtube how to replace it. It took about 25 minutes from start to finish to install. works like a new one. Thanks partselect.

Got the latch kit, found the correct one, popped it in...dryer works! Thanks....

I had to opcn up dryer, remove drum and replace worn parts.

follow the vidio. removed lint screen. removed screws securning the lint trap guide. used to disconect the two clips honding the top cover and lifted it up and secured it as not to drop down. removed two screws at top of front paned and removed it. took out drumb. took off the two rollers and remounted the drumb and belt. replaced front panel and two screws. lowered top panell and two screws. replaced lint trap. turned on to see is noise stoped and it had. done

It was fairly easy, the comments and pics on this site were quite heplful. I just took out the screws on the lint trap and popped the top by pushing in on the clips with a putty knife. zlift the top and swing it back. I cut the old belt with a utility knife since i was replacing it and lifted out the drum. the drum wheels just pop off and on so they are really easy to replace. next I took off the old rear seal with a putty knife and put the new one on. This is a messy affair if you are not careful, I ended up with adhesive all over my hands. Next loop the new belt over the drum and replace it aligning it. You kneed someone to help you hold the drum level while you replace the belt wheel and front. Run the drum around with a putty knife under the new seal to make sure it is not tucked under anywhere. Put it all back together and you are done.

I had knee replacement 2 weeks before our dryer stopped working! My wife took the rear panel off & replaced the parts under my reading the instructions ! Very easy to replace!

Having read the instructions and watched the tape, I pried out the remaining catch with a flat screwdriver, read about what the color scheme on the parts wasbout and pushed in the correct part. Voila ! Done in probably two minutes.(By an 82 year old woman!)

The dryer belt was delivered promply, afterwards I lifted the top of the dryer and unscrewed the front panel, so it would lower. Then I watch a 5 minute video and it clearly demonstrated how to install the belt. This was my first time, so it took about 30 minutes.

after replacing my heating element, my dryer still wasn't heating. So i replaced the thermal cut-off unit. from ease of finding the part, to ordering and the instructional videos...this was a no-brainer.thanx guys!!

PartSelect sent the exact right part, and very quickly! YouTube showed me how to install it. The only hard part was the bulkiness of the drum, which is why I marked "a bit difficult" for the repair.

Got online with parts select, easily found the parts needed and ordered them. They arrived very quickly. The repair itself took all of 5 minutes and now the dryer door stays shut like it is supposed to. Only complaint is shipping was more than the parts but then again, I didn't waste a lot of time running all over town looking for what I needed. So, in the long run I saved money , especially when compared to a calling someone else to fix it.(big bucks for even the most minor service call as you all know).

pop off put in done