KEYE660WTO0 KitchenAid Dryer - Instructions

Removed the current (broken) block by unscrewing the screws at each end. I decided to re-use the wires / connectors in the dryer, though. The connector on the dryer is held in the block by a bent tab, about half way along the connectors length. I pushed this with a screwdriver and pulled the connectors off the current block. Sometimes I had to re-bend the tab prior to putting on the new block. Then I slid the connectors into the new block. To do this, first you put the captive nut into the slot, and then you put the metal end of the connector below the block, so the wire is around half-way down the block. Then slide the metal in, trying not to pull on the wire. Lastly I reattached the block to the machine using the two screws. Didn't need the terminal block screw kit, as these parts were in the block-term kit.

always unplug from outlet first, unscrewed the back off and pull off the wire from cycling thermostat ,take the two screw out that holding it in place and replace the new one .Very simple and easy. Thank you for the easy step by step video to complete this repair. James

Instructions are available from other web sites. A few tips from me. Tape the dryer doors shut. When you remove the springs it falls open. Remember to just loosen the hex screws at the bottom of the front panel, it has slots and just lifts off of them. To easily remove the clips holding the motor bearings use a dull chisel or small pry bar on the outside half loop and tap the end with a hammer while lightly forcing it out.

Took old bearing off replaced with new

Watched a you tube video on replacing a dryer belt for a whirlpool dryer. Perfect instructions. Dryer is working great.Thank you

I'm a 66 year old lady with no repair experience at all!! I found the part I needed on Parts Select, which I ordered and received in less than 4 days. I watched the video that you've posted on your website which shows in great detail how to do this repair. It looked like a simple fix and it was!! I highly reccomend Parts Select!! Took my granddaughter(held flashlight) and myself less than 30 minutes to do the repair!!!

video on your website made it super easy

This is a straightforward repair that you can do in an hour or less. Open the lint trap and remove the two screws. Use a screwdriver to pop up the top of the dryer. Remove two screws that attach the front panel. Now you can lift out the drum and then lift off the front panel. Clean out all the lint. Make sure the motor pulley turns smoothly. Tilt back the dryer diagonally to make the rest go easier. Loop the new belt around the drum (rubber side down) and reinstall the drum against the back wall of the dryer. Make sure the cloth liner fits perfectly around the ridge, with no folds so the drum rotates easily. Make sure the drum fits smoothly against the two rubber positioning wheels on the back wall. Position the new belt around the center of the drum. On the dryer floor, stand up the tensioner bracket. Tricky part -- thread the belt so it runs through the bracket and loops around the drive pulley on the motor, rubber side against the pulley. The belt should be tight, held by the tensioner. Reinstall the front panel so the opening aligns with the drum opening. Drop the top down, snap into place.and reattach the screws in the lint trap. Done!

Removed the old one installed the new one

so being the WOMAN that I am I decided to take it apart. well low and behold I found out it was the pulley and belt so I decide too order from parts select easiest thing I've ever done yay me

Watched the tutorial online. Took the back off- replaced the fuse. Put the back on . It was extremely easy !!

The online vidio was very helpfull

The repair was easy--thanks to your excellent videos--also, delivery was prompt and correct--your service is excellent--but, looks like I'll need another part--maybe door latch??? I'll troubleshoot and definitely contact PartSelect--Thank you--will recommend you!

We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.

I removed the back panel of the dryer and the thermal fuse was about three quarters down the dryer. The exploded parts schematic was very helpful. I simply removed two screws to replace the thermal fuse and reinstalled the back panel. The dryer works great now.