KERI500EAL2 KitchenAid Range - Instructions

I got the new wheel and screwed it in by hand. It took like 4 minutes total between taking out the drawer, screwing the new wheel on, and putting the drawer back in

The part came in 2 days even though I chose the least expensive shipping method. The hardest part was unscrewing the old screws that held the old bake element in place. We soaked them in WD40, and after a while were able to unscrew them. The new element slid in place and works just fine.

The oven light gasket had deteriorated with time and bulb changes. It is a self cleaning oven, which gets very hot during the cleaning cycle. The oven is old (27years) and off the "books" I selected a similar, but slightly smaller gasket (3" OD), and "fit" it to the 3.5" light fixture of the older oven. The gasket material was similar to the original, and I used a usable portion of the original,along with the new gasket to build a gasket for the light lense. Several years prior to this repair, I replaced the oven door springs. Whirlpool, who had taken over what was left of Chambers, had the springs. I did replace one heating element about 15 years ago. The Chamber's salesman told me that the Chambers was the "Cadillac" of all ovens, and it seems to keep running.

burner replaced

Had to screw off old terminal block & screw on new one

Replaced both rollers....Quick and Easy!!

TURNED OFF THE POWER TO THE RANGE, DISCONNECTED THE ELECTRIC PLUG. I unscrewed the element attached to the oven, disconnected the connectors. Reconnected the element and screwed the part back to the oven. EASIER THEN I THROUGHT.

It was difficult to reach the back of the oven inside to remove screws. I had to use an extended socket with a bit tip. When I tried to remove the element from the clips, the clips slid back inside the insulation at the back of the oven. I had to take the back panel off of the oven, push the clips through the opening and then I used a bag clip to hold them so they would not slide back into the opening. I could not lift the door off-too heavy- to get closer to the back of the oven to put the clips and screws back on so I laid the oven on its back after putting the back cover on. The oven door was so heavy then that I had to prop the oven door open with my 24 inch rolling pin. I then leaned down into the oven and managed to get the clips and the screws back in. I then put the oven upright again, plugged it in, then had to re-level the whole thing. I turned it on and it worked. This probably would have been easier if I were not 65 years old and had some help. I was not giving up though. I got it done.

Turned off electricity at breaker, slid stove out from wall. Disconnected unit. Removed back panel (4screws). Disconnected double broiler wires from the back. Unscrewed element bracket from back wall of oven (2 screws). Removed and replaced element and replaced screws to back wall of oven. Reconnected wires on the back of the oven where element connectors protrude from oven wall. Replaced back panel (4 screws). Removed oven door by pulling forward (no screws involved). Removed screws from bottom of door holding trim on (7 screws). Removed bottom trim and side trim. Removed front glass. Removed inner portion of door (it's just stacked together sandwiching some insulation). Removed track holding 2 glass panels (6 screws and pressure brackets). Removed one screw from corner of track. Removed and replaced inner glass. Lay door flat on floor front down to reassemble. Place glass insulation (looks like rope) around window opening. Lay the track containing he replaced glass down (side with most shallow recess). Replace 6 screws and pressure brackets. Replace large insulation and inner door panel. Reinstall front glass in slots under door handle. Replace oven door back. Reinstall side and bottom trim in reverse order to removal. Replace 7 screws along bottom of door. Reinstall door assembly to oven by sliding tabs back into the range. Done!

removed the screws that secured the lower element. Disconnected the old element from wire contacts. Inserted the new element into the wire contacts.