KEBI171DBL7 KitchenAid Wall Oven - Instructions

Shut off power at breaker and removed oven door to lessen weight. Removed oven trim and retaining screws and tried pulling out of cabinet. Stuck on power cable, so had to remove Mircrowave oven above to get to power cable plug. Removed oven back cover panel to access thermostat. Easy to unplug and replace with new thermostat. Reassembled and turned on power. Cooked dinner in oven.

I removed the two stainless trim pieces (2 screws) and then two screws which hold the oven frame to the cabinet. Be careful to put a pad on your floor before you pull the oven out of the cabinet as there are sharp edges on the bottom of the oven. I removed apprximately 12 screws holding the back panel in place. The fixed set point thermostat is in middle toward the top of the oven cavity after removing the rear panel. Just remove two screws and slide the terminal connectors onto the new thermostat. Very easy job for someone who is not too handy.

Repair was fairly simple, unscrewed oven from cabinet and pulled it out. Then remove screws on back panel to access the thermostat location. Unscrew old thermostat, unplug it from connectors and plug in new thermostat. Then screw back in place, replace cover and pop oven back in place. Now fire it up, worked for me! Thanks to part-select. Good luck everyone. Probably saved $200 service call.

After 22 years the oven stopped heating in the middle of a meal prep. The fault code was F3 oven temperature problem. I googled the codes and found PartSelect described the problem and the repair and part needed. I received the oven sensor part, then turned off the power, used a screwdriver to remove 2 screws (had to find the right size flat head screwdriver to fit the square holed screws and they were pretty baked on after 22 years of use), gently pulled the sensor and wiring through the back of the oven. I used a needle-nose plier to pull the plastic connector through the insulation, then unsnapped the connector, snapped in the new sensor connector and pushed it back through the oven wall. Pretty simple repair, took me longer to find the screw driver than the actual repair.
Thank you PartSelect for making it easy and saving me a repairman visit!

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

Originally ordered just the spring assuming that might be it and it was the cheapest way. However after getting in I found that the latch assembly had a broken 'tit' that is intended to hold the metal latch in place as it moves. Attempted to glue w/ epoxy but as i expected there was too much pressure to hold it in place. So....ordered the assembly.

TURN OFF BREAKER.....

1) Remove the two side rails by removing screw on the inside bottom of rails.
2) It helps to remove the door to get it out of your way but not required. To do this open door fully and insert two nails or similar into holes on each hinge. Close the door until the hinge contact nails. Lift the door up and out.
3) remove the top control panel by removing screw on either side (outside of oven)and screws on the underside of panel behind upper door.
4) It help to completely remove the panel to have more room to work but not required. If you do it is a good idea to photo the cable locations so it is easy to recall where they go. For the most part they only fit one location but always a good idea.
5) remove the latch by removing all spade connectors and two screws in front.
6) place new latch and reassemble.

Remove the left/right outside trim on the double oven. To do this you will need a phillip screw driver. There is only one screw holding each side located at the bottom of the trim (on the inside between the trim and the door). Remove the trim by pulling out and down. Remove the bottom trim by removing the screws located on the outside of the trim. Remove the trim by pulling down and out. Replace the new trim by reversing the process making sure to replace bottom trim first because the outside trim goes over bottom trim to cover up the screws on the bottom trim

removed double wall oven light lens install bulb replace lens fini

After turning of the breaker for the oven, I pulled out the oven, removed the back panel. The High-Temp thermal cutoff was attached to 2 wires, which I unplugged, and then removed the cutoff by removing two screws. I then replaced the part in reverse order, pushed the oven back into the cabinet, and turned the breaker back on.

First remove the side trimmings by opening the oven door and taking out the two screws near the bottom. Remove the bottom trim by removing the two screws now exposed. Here's the hard part .. The outer glass is held by 4 screws 2 at the top and 2 through U brackets at the bottom. You must remove the 2 bottom ones first and then VERY carefully, whilst supporting the glass remove the 2 top ones and then gently pull from the bottom to release the glass at the top and pull away. The rest is straightforward. There are 4 glass pieces to remove, make sure you clean the finger marks off as you replace them. I would suggest 2 people to replace the final outer glass 'to be safe"

we live in Venzuela the ordered windows come to us via a forwarder in the US, one glass (the outer glass) still has to arrive. Very pleased with the service of PartSelect, one glass was in stock, the inner glass had to be ordered with the manufacturer. This glass is on its way and will arrive here in Venezuela by the end of May. As I have to travel to Europe next week, I will install both glasses upon my return somewhere in August next. I will sure inform you about the repair which will be done by myself.
regards,
Titus

Thanks to video provided by PartSelect the repair was fast and easy. My second experience with an appliance repair with parts and video from PartSelect. I am a happy customer.

I watched the video on the product page and followed it step by step. Not difficult at all.

My oven (late 90's/early 2000's model) didn't have the flip-down hinge locks shown in the video. It seems Whirlpool/Kitchenaid changed the hinges even though they didn't change the model number of the oven. With my style hinges, you have to put Allen wrenches or bent nails in the holes just behind the hinge pins. Then close the door almost all the way and lift it out to separate the hinges. Spring force holds the nails in tightly until you replace the door. This video was very helpful:
https://www.youtube.com/watch?v=p7oRZdIN6m0

Also, my door had 3 different kinds of sheet metal screws. Two of them have similar heads but different threads. Keep track of which is which for when you put everything back together.

Easily, Removed the oven with help of my grandson, this model is quite heavy. Open the back cover panel, removed the old blower. replaced with the new blower, covered with the back protective panel. About one hour because some screws much harder to reach.