KEBI100VBL3 KitchenAid Wall Oven - Instructions

I read other other posts and followed their advice. Remove the 2 screws holding the element to the back of the oven...gently pull it out about 3" to reveal the connecting wires. I found the needle nose pliers were necessary to detach and reattach the wires. Don't yank! Be aware that the wires have a tendency to want to pull back into the back of the oven while they're loose. This was a wall oven and that woul've been a large problem if they they had. Otherwise it was a snap!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires fom the old element .. connected them to the new element ... put the screws back ...and tested. problem solved

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy

Naturally the oven turned was off but for added safety I also set the breaker protecting the oven to the off position. Where the element attaches to the oven there is a small plate with two screws holding the element in position. Remove these two screws and then gently pull the element out 2-3 inches, which will expose the electrical connection. Using needle nose pliers gently pull on one of the wires to remove it from the element. Now remove the other and discard the old element. Simply plug the new element into those wires and screw the plate back into the oven. Now turn the breaker back on and you're done. Super easy!

removed 2 screws . pulled out the 2 wires and disconect them. took out the element. Put the new element in and hooked the wires up. placed the metal bracket to the back and put in the 2 screw and turned it on and it worked like new.
Brenda

I removed the back panel, unplugged the wires, removed the 2 screws, replaced the element, plugged the wires back in and put the back panel back on. Now that I'm thinking about it, I guess I didn't even need to remove the back panel to replace the element.

Removed old element, replaced new element. Unfortunately, this didn't fix the problem. It was the temperature sensor. But now I have a new bake element, though!

Piece a cake!
Turned off electrical breaker.
Removed original screws from old defective element and slipped in new replacement element.
Perfect fit!

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

Turn off the oven circuit breaker. Remove 2 screws that hold the element in place. Carefully pull element out, about 3 inches and remove 2 attached wires by holding the element and pulling the wire clips off of the old element. Slide wire clips onto the new element and put the screws back in.

was very easy to install I only needed a phillips screwdriver to remove old part and install new one.

Remove racks, extract two phillips head screws, pull out element, unattached wires, install new element, reverse procedure to complete installation. (Note: With the racks and element out, great time to clean oven.)

Took a phillips head screwdriver and took out the two screws. Lifted off small plate securing screws, pulled lightly and wiggled the element out and popped the new one in. Total time 7 minutes - yes we timed it!!! Fast delivery too!!!

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

The replacement of the glass was easy, I removed the door and placed on work bench. As long as you lay the parts out in an orderly manner the reassembly goes pretty good. The longest time was cleaning the glass's that were dirty from the inner broken glass.
I also reconnected the self cleaning oven lever this required the removal of the oven top. Lot of screws to remove but went ok. I put locktite on the two screws which are extremely short.