KBRS22KGAL2 KitchenAid Refrigerator - Instructions

1st remove the gasket from the packaging & let it get to room temperature . 2nd use a hair dryer to get it in shape . 3rd cut out a piece of the box that the door gasket was delivered in to cover the freezer opening after you remove the door,4th(remove the door by removing the bottom hinge) 5th put the door on a table to remove the old gasket with a screw gun,(now is a good time to clean the door up) after the old gasket & panel was removed I found the insulation inside the door panel frozen solid so I replaced it .If you don't replace this fiberglass insulation or a least try to thaw it out you defeat the purpose of the doors insulations R value. 6th replace the gasket (replace the gasket the same way that you removed it) 7th put the door back on the freezer.You don't have to remove the freezer door to do this job but it makes a much neater job & a better seal when the door is closed. This isn't the 1st door gasket I replaced so I kind of knew what I was doing.Good Luck

Turn freezer section control wheel off, unplug unit. Then remove all items/baskets from freezer to allow access. Use nut driver to unscrew 3 screws on control plastic housing. Drop down housing from top and unplug wires (note correct locations) from control wheel switch. Remove screws and ground wire from metal backing plate to plastic housing. Push or pry the 2 metal holdtabs down carefully to allow the 2 plastic housing tab fingers to be pushed inwards to seperate metal plate from housing. Pry control wheel off from switch arm with screwdriver. Remove switch and replace with new one.
Use the reverse order of removal above to replace into freezer but use caution when replacing wheel onto switch arm and plugging in wires. Remember to carefully pry the 2 metal tabs back up to secure the plastic finger tabs in place.
Job done.

I called a repair man from a pretty large name to come out and take a look. He found out in about 10 minutes that it was a bad capacitor. The quote he gave me was $75 for the part and $175 labor. I tried my best not to laugh and tell him no thank you. He did have to charge me for him to show up, which was only $98.
So I used what he told(minus the "scrap it") and opened it back up. Although he had left wires everywhere and the broken pieces laying inside, I thought it was enough for me to order the part. PartSelect was very easy to navigate and ordering was a breeze. Took about 4 days to get the part and I ordered in the X-mas craze. Fixed it in about 15 minutes.

First step, call the repair man. He listened, and then said to get a new refrigerator, since this one is 28 years old and the repairs could amount to a significant part of the price to buy new. Even if he fixed this, it could develop other problems, yada. So we went out to buy and discovered nothing suitable that would fit in that slot of our kitchen! We'd need new counter top and cabinets to fix this problem! So we went to the Internet and searched to find the likely source of the problem and the parts schematic at PartsSelect.com. Yah! We ordered the part, and then found we had no idea how to install it. Sooo, back to the Internet, and eventually got some good clues - it goes in the kick space under the front, and just plugs in, once you can get to it by removing the bracket that holds it. Working underneath a refrigerator is not complicated but it's awkward. The form of the new timer was not exactly the same, but it does function correctly. We have no experience whatsoever with appliance repair, so pretty amazed at our success. This old Amana looks very good inside and out and is now working perfectly again. If it lasts a few more years, we will be thrilled to have spent $15 to save $500. We can always buy new later on.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

Research on the internet showed the problem was either the defrost thermostat or the defrost timer. I decided to replace both.

1. Emptied the freezer into an ice chest

2. Removed shelves, some of which were held in with screws.

3. Removed freezer back panel.

4. Replaced freezer thermostat, very simple, one clip and two wires.

5 Replaced all removed parts. Put food back in freezer

6. Removed and replaced defrost timer from underneath front of fridge, screws were awkward to reach.

7 No more heat around outside of freezer

If you can take the old one out and reverse the procedure, there isn't much more to it than that.

I removed the panel in the back of the freezer and found the evaporator to be a complete block of ice. I defrosted it with a hairdryer. Following advice from the Partselect web site, I measured the resistance through the defrost heater. It was about 30 ohms, so I decided that it was OK. Next, I advanced the defrost timer manually with the compressor on until it turned off. The defrost heater did not operate. I concluded that the problem was the defrost thermostat. After installing it, the freezer worked properly.

Remove old parts, install old bar to new caps and snap in place. So easy even a caveman can do it!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I removes all food and drink items from the refrigerator and freezer doors. I then removed all of the screws holding the inner panel of the refrigerator door to the door itself. The old gasket could then be removed. I placed the new door gasket in place around the inner panel and reinstalled the inner panel with new gasket onto the refrigerator door. I then removed the inner panel from the freezer door and then removed the old gasket. I placed the new door gasket in place around the inner panel and reinstalled the inner panel with new gasket onto the freezer door. I used a portable drill with a 1/4 inch nut driver to remove and reinstall the many screws that held the inner panel and gasket on the doors.

Soaked the gaskets in bathtub to make them more pliable. They laid flatter and were easier towork with,

It turned out the water valve was not the problem but I think it works a bit better with the new one. I had replaced the main part of the icemaker inside the freezer which had lost the smooth finish in the ice tray. It worked for awhile but quit.
What had happened was the large approx. 1/2 inch tube going from the back of the refrigerator to the icemaker tray became plugged with ice. It was difficult to get it out due to the ice but once I did it was easy to melt it and put it back together. All's well that ends well and avoid the cost of a repair call. Working great now.

Because the refrigerator worked (38-40 degrees) and the freezer only got down to 29 degrees, I thought that the freezer thermostat had gone bad. Changed it out but results are the same.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!