KBRS20EVWH3 KitchenAid Refrigerator - Instructions

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

Piece of cake. Took out old filer and put in new one!

Opened filter area door turned old filter to the left to unscrew. Took out old filter then replaced the new filter and turned it to the right to tighten it, closed cover and that was it all done.

It was very easy I just push ito n and it snaped right in.

removed old icemaker and transfer some of the parts to the new icemaker. The only problem was that I had to disasemable the new icemaker to replace the fill tray with the older style (which was included). Once that was done, installation was pretty easy.

I removed the old ice maker as described by the DIY video and had no problem except, I had to remove the ice tray from the motor section so the end cap could be changed. This only required removal of two Phillips screws on the case of the motor assembly, that are used to to secure the tray. Once the tray was off, the ice ejector could be removed and the end cap was free to change. Everything was re-installed in reverse order and unit was mounted. An FYI to anyone with slow ice making, will need to check their freezer temperature. Make sure it's set to get as cold as 5-10 degrees Fahrenheit. After installing new maker, it was not making ice fast enough, only to find my freezer temperature needed to be changed as well. Everything is working as it should now.

The ice maker was easily replaced, however I still had no ice. I ended up using an on-line repair service which determined that the problem was the water inlet valve. Replacing it was beyond my expertise so I hired an appliance repairman.

Replaced part--4 hexhead screws. This is my third time changing this part (right and left) and was happy to see that an obviously under-engineered design has been modified. The pin bracket has been reinforced and appears much stronger.The most time consuming portion of the fix was cleaning off the shelves for removal. Thanks for asking. Norm Notdurft

After reading the articles previous owners wrote, I tackled the repair. There were no big problems until I had to change out the water line on the icemaker tray--that part was for a different frig--so it had to be changed out with the Amana water line part that was enclosed. I couldn't get that part removed, so I had to have my husband change it out. He then finished the installation. Everything went smoothly, just my pride wanted me to finish it all by myself.

Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

I watched the on line you tube video on how to DIY. The putty knife worked to pop out the switch. I used the standar screwdriver to unplug the switch from the wire harness. Then plug in the new switch and pop it back in to the roof of the freezer. Tip: watch out when ordering the new switch - the freezer switch is different than the refrigerator switch. The freezer has three prongs. The fridge has two. I initially ordered the wrong part and added a week to the repair time and had to pay shipping to return the first switch.

got the model number off the fridge. ordered the part. received the part. the funnel part that drains the water into the tray was broke when I received the new icemaker, I took the one that was on my old leaking icemaker an put it on my new one along with the old hardware parts {wireharness, ice level bar}. followed the video instructions an wahlah nomore ice in the bottom of the freezer or in the floor. it looked like the funnel was broke in shipping. its great to have ice because its fixing to get hot!