Models > KAWS777EQ0 > Instructions

KAWS777EQ0 KitchenAid Washer - Instructions

All installation instructions for KAWS777EQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KAWS777EQ0
1546-1560 of 1607
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

when it would spin it would sheakall over .

  • Customer: Johnny from Las Cruces NM
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
just did it how the way it showed on the video it was easy

Washer vibrated during the spin cycle

  • Customer: David from Roswell GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The repair took about an hour. My wife told me the washer was so quite that she had to check and make sure it was running. It was like getting a new washer for less than 30 dollars. I've saved Part Select web site to my favorites and will use your company again.

Drum moves and strange noise when spinning

  • Customer: Kenneth from Hillsborough NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
When I pulled the machine out, I noticed one of the suspension springs on the floor. I followed the video supplied by PartSelect.com and suggestions by other folks. I started with the spring that was missing, which was a mistake since I did not know that there are custom spring clips which hold the spring to the drum. Once I found the missing part the installation was very easy. I used the suggestion by another post, of wedging a block of wood between the back of the machine and drum, to relax the rear suspension spring, which eliminated having to remove the back of the machine or tipping the machine on the back to get at the screw. I will always look to PartSelect.com for any future appliance repairs. You are the greatest

Loud bang at the end of the spin cycle and symptoms of an unbalanced load.

  • Customer: mark from murfreesboro TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After reading everyone elses stories, I purchased all new springs(5), new spring brackets(one of mine was rusted really badly)and all new wear pads(two sets of 3pcs each). The rusted spring bracket was the most time consuming as the screw was rusted into the bracked so I had to drill it out. Other than that, the actual spring replacement was easy. Took maybe 10 minutes. The wear pads were another story. I'm a pretty good mechanic and I had a bit of a struggle getting the old pads out. I used a long, flat head screwdriver to pry them out. Once they were out the new ones weren't too tough to get back in. Took about 20 minutes all together. I stongly recommend watching the video on removing the washer cabinet first. It will save you some time. Acutally, watch the videos on all of the parts to simplify the process. Oh and by the way, all of my washer problems are gone. Well worth my time and $70 in parts. Good web site!

Out of balance on spin cycles

  • Customer: Darren from Saint Jacob IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the top part of the electronic panel. Removed the top lid. Removed the old tub springs and replaced them with new ones. Works great and for only $20.00. It beats buying a new washer. Thanks!

Cam in top of agitator was broken.

  • Customer: Richard from Palm Springs FL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Followed the fantastic video instructions and replaced the parts to make the repair. Very easy and all works well.

did not spin all the water out of clothes (clutch was slipping)

  • Customer: donald from alexander NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
followed repair instruction,( bought on line and down loaded ) some instructions were unclear but when you have the machine apart its obvious. your parts breakdown helped more than the instructions once the cabinet was opened.

drum wouldn't empty, washer stuck at that point in cycle

  • Customer: Steven from Chapel Hill NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Looked on line at Parts Select, and noted there was 66% chance that problem was in lid switch. Stuck screw driver in slot under lid, pushed on switch and made washer work, verifying that problem was likely in switch. Ordered part. Disconnected washer from electric/water. Removed screws on back and sides of panel; lifted lid and cover; replaced switch; reinstalled cover. Reconnected to elec/water. Worked. No problema.

Hanger on motor broke and destroyed the coupling

  • Customer: Andre from Torrance CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Turned machine on it’s back after removing the hose that goes to the drain, removed the bottom dust guard, I removed the hoses (take a picture before removing things so you know how to orient them when putting it back together) and drained the water first but this is not necessary (there are YouTube videos where they suggest removing the outer case, unclipping the pump and then removing the motor. This would be optimal as you don't need to deal with the water running out of the washer when you remove the hoses). Removed the 4 electrical connectors (multi-plug, 1 x two prong plug and 2 capacitor connector plugs) One of the motor hangers were broken on my machine, I removed the other one and then slipped the motor out. Removed the broken hanger and securing screws and the old rubber grommets, slipped the coupling out (had to leverage out with a large flat screwdriver). Installed new coupling and rubber on the gearbox side, 4 grommets on the motor and the other coupling on the motor. Inserted the hangers on the gearbox side and then mounted the motor. (it is easier if you turn the washer on its back so the drum moves down and gives you more room to drop the motor in from the top), clipped the motor hangers on and fastened the two metal screws, mounted the pump and hoses and reinstalled the dust guard. Turned it right side up and tested before dragging it back into the laundry. Washing again like it did when first bought it in 1998. I would recommend that when a coupling brakes, replace it as well as the hangers and grommets to make sure it has no room for play. Mine broke way too quick as I did the last coupling about a year ago, problem I think was that I had the wrong grommets causing excessive vibration and wear.

washer wouldn't go into spin cycle; water would be pumped out.

  • Customer: Nora from Village of Chamita NM
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
I went to Google internet search engine to look for a website that would provide an answer to problem with washing machine. After trying out a few websites it became apparent that these sites were not going to give me a fix it solution. With the grace of the gods of IT, finding your website was the answer. Your website quickly identified my model number and opened up a wonderful page which had a complete break down of my washing machine, and I might add with the most likely reported problems from other do-it-yourselfers. The part is prices reasonably, and placing an order was easy. PartSelect’s online instruction for part installation is a reason for becoming the favorite to all do-it-yourself people. Nora

MACHINE WOULD NOT SPIN & REMOVE ALL WATER

  • Customer: ROBERT from CARROLL IA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Followed instruction found on line, they were very helpful and very well done by tech. I have a back ground in appliance repair mostly GE. I find the design of whirlpool washing machine was very well done, the repair of all major parts was easy and simple. Best designed washer I have ever worked on. Delivery of my needed parts was fast. I put parts in the machine it really didn't need, felt I could get another 10 years out of the appliance. VERY VERT SATISFIED, THANK YOU

Upper agitator quit working properly.

  • Customer: Dan from Edinboro PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I followed the video posted on the parts diagram page and the install went flawlessly. Also, I am extremely pleased with the ordering process and speedy delivery of the parts that I ordered.

Slow spin cycle.

  • Customer: Stephen from Hernando MS
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Found Website and entered model number. Used the quick explanation of problem to find required parts for repair. Found that one washer was left off in the parts recommended for repair while repairing that was purchased locally because it was cost was lower than part and shipping on line. The parts ordered from Part Select arrived with in 3 working days. Video was very helpful for the whole repair.

Lots of gunk between fabric softener dispenser and where it attaches to the agitator

  • Customer: Gregory from Sandy Springs GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Rubber O ring around the Inner Cap was rotted and busted through. Replaced with new Inner Cap Seal. Easy as pie!

Agitator not working properly, directional cogs had broken

  • Customer: Marshall from Franklin NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Removed fabric softener dispenser and agitator cap barrier. Used ratchet wrench with extension to remove the 7/16" agitator bolt. Lifted out the agitator unit and disassembled it, removing the broken directional cogs. Replaced worn thrust spacer (used white lithium grease to lubricate), directional cogs and inner cap seal. Reassembled and reinstalled agitator unit.
All Instructions for the KAWS777EQ0
1546-1560 of 1607