JW3000W Jenn-Air Washer - Instructions

raised the top of the washer to get at the front panel screws. Removed the front panel. Removed the cracked hose and installed the new one. Reinstalled the front and top panels.

Removed front panel by releasing spring clips with putty knife and removed two screws with a ratchet and 5/16” socket. Removed rear access cover with a ratchet and 5/16” socket. Removed and replaced tub to pump hose. Loosened clamps on each end of hose with channel locks.
Re installed rear access cover and front panel.

Easy repair - with the use of a phillips screwdriver, simply remove the old device and replace with the new

I watched the video of the repair on this website and followed it. Was really easy & THANK GOD because this was my first repair. This has been a great machine and it looks like it will continue to be for a little while longer! Thanks for the video help and friendly navigation of your site!

First I got everything I needed, unplugged the washer. Using the puddy knife I freed the top of the washer by inserting the knife about four inches from each side on front. The machine is in a place where it can not be pulled out far, hence the two by fours. Remove the loose cover, reach in with the stubby and unscrew the screw on both sides. Take the broken cover pins off the cover and install the new ones, put the other hinges in the cover, put the hole cover in place and install the one screw perside, remove wood and close the hole top, your in business , no drinking

I first changed the belt which helped but it still sounded like it was going to take off through the roof.....I did the pulley and bearing kit in hopes that it would do some good....it went really smoothly with no issues however it did not solve the problem....so it is working and I am going to just ride it out until it quits....thanks

Rolled the old one off and rolled the new one on.

I followed your video instructions. Very good video.

I raised the top of the washing machine per video instructions, removed the screws, replaced broken hinges with the new ones. It was simple as that.

Tilted machine back, put a paint can under it and did R & R with belts.

I had my boyfriend take the lid off ,then he took off the two old hinges,one was broken,and the he replaced both lid hinges,daving the good one. it was very simple and quick for him.

Iwill use your service again,thanks.
Loyce Floyd

I moved the washer out from the wall. unplugged washer, turned off water. Took off rear plate exposing pump. Disconnected hoses, using dry/wet vac to catch water. Took out three screws holding pump to base of washer and removed pump, belt slipped right off. Set new pump in place and put in screws. Connected hoses, put rear plate back on. Tilted washer back and installed belt on pulleys and motor. Turned on water, plugged in washer, started to wash clothes. Washer works fine and QUIET. I have yet to find the model number on my Maytag washer. I ordered the pump by sight (good pics).

Disconnect Power. Disconnect supply hoses. Open top by releasing top retainer clips with a thin blade or putty knife. Remove 2 sheet metal screws retaining front cover. Remove front cover. Lay a blanket on the floor and lay the machine over on its side leaving access to the front where the panel was just removed. Take belt off. Remove pump hose at bottom of drum. Prop up drum so it is centered in its normal position and not laying to one side. Do this near the lid end. Remove all centering springs - carefully. Drum and transmission assy will now come out through the front opening. Flip drum assy upside down with transmission up. Loosen the screws (do not remove completely - WARNING OF 200 LBS SPRING LOAD!) that clamp the snubber ring to the transmission. Remove the old snubber ring and replace with new. Be sure it is completely under the flange all the way around. Tighten the retaining ring screws. Reassemble all parts in reverse order. Done. Be sure to level the machine per owners manual instructions.

remove top and front panel to access wash drum. unhooked suspension/balance springs(6).also removed drive belt. removed half of brake bolts installed 3 1-inch bolts removed 3 remaining short bolts,then 3longer bolts to remove tension of brake spring. removed/dissassembled brake and snubber ring,then reassembled in reverse order. wish i would have replaced suspension springs at same time! ordered new springs today

I had my 12 year old son climb to the back and he took off all the screws necessary in the back and took the part completely off. We ordered the part and waited for it to come in. We replaced the part, the screws and honestly, the only thing we had trouble with was replacing the small cover where the hoses stick out of the washer. Was an easy efficient experience that may have saved me $300.00+ dollars. Thanks to my 12 year old son we got her fixed up. The washer works like brand new.