Models > JVM231WV01 > Instructions

JVM231WV01 General Electric Microwave - Instructions

All Instructions for the JVM231WV01
76 - 90 of 184
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Still runs even the door was open
Pulled it from the wall remove the front vent covers removed the control panel remove the door switches by a special screw driver bit which looks a star remove the electrical terminals pressed the plastic clip pulled the switch replaced it with new one then followed initial steps backward
Parts Used:
Monitor Door Switch Secondary Door Switch
  • Erwin from CONROE, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken handle
Exact Fit, Took about two minutes using phillips head screw driver.No problems
Parts Used:
Door Handle
  • STEPHEN from Albany, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Handle was broken
Removed old handle. Cleaned area on microwave door. Screwed hanle on.
Parts Used:
Door Handle
  • Aubrey from Silver Spring, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave handle broke off
I removed broken handle, then simply attached the new handle with two screws.
Parts Used:
Door Handle
  • Richard from Skillman, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
microwave Quit working but lights worked
llation
Parts Used:
Secondary Door Switch
  • Rick from Muncie, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
5 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bulb burned out light that is under the microwave, which lights the oven below.
thank you for the video--very clear, responsible, applicable although the illustration was not exactly of our kind of light. the bulb was exactly like the one Hotpoint used in its microwave made in 1989! I will come back to you for parts in the future. (You have the model # from my original order.)
Parts Used:
Light Bulb - 40W 130V
  • Gary from UNIVERSITY PA, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Under the microwave there are two light bulbs that light up the top of the oven/range.
Last week I removed the glass cover that was held in by one screw and removed the burnt out light bulb. I ordered the bulb and left the glass cover off until the bulb arrived. I had to wait until this evening to put the glass cover back on and fasten the screw because I have a window right next to the oven and the sun streaming in made it too difficult for me to see how to put the glass back in and replace the screw.
Parts Used:
Light Bulb - 40W 130V
  • Janet from TREASURE IS, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door handle broke
I removed the one screw, the other end was broke. Replaced the handle. At first it didn't screw in tight, so I turned it around and put in both screws and bingo, good as new. Thanks for your quick response. Was simple.
Parts Used:
Door Handle
  • Elizabeth from Santa Rosa, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the handle was broken
just screwed the new part
Parts Used:
Door Handle
  • Jorge from Pleasanton, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken door handle
Real easy------Removed two screws, handle & replaced same.
Parts Used:
Door Handle
  • Gerard from Naples, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave oven handle broke loose at bottom of door.
Philips Head #2. Two srcews out....two screws in. A perfect fit!
Parts Used:
Door Handle
  • Richard from Concord, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The handle broke at the bottom.
I removed the existing screws and removed broken handle. Wa able to still use existing screws and install new handle. Very easy.
Parts Used:
Door Handle
  • Darenda from Houston, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door handle on my Space Saver Microwave broke at the screw mount
It was very simple...there were two screws on the inside of the door that held the handle. Removing the screws was easy and the new handle lined up perfectly. I replace the screws and the whole event took less than 15 minutes. The handle arrived from PartSelect the day after I ordered it and even though they had projected 3-5 days for delivery.
Parts Used:
Door Handle
  • Vance from Alexandria, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
handle didn't come w/new screws
I had to shim the outside to get the door tight,the original screws are longer than what the current handle requires.For the price ,new screws should be a part of the package.
Parts Used:
Door Handle
  • steven from wilsom, NC
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Door Handle
Removed 2 screws. Placed new handle in position. Installed 2 self tapping screws. 2 Minutes to find phillips screwdriver, 1 minute to install screws.
Parts Used:
Door Handle
  • James from Berwick, IA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JVM231WV01
76 - 90 of 184
Back to Top