JSD2789GEW Jenn-Air Refrigerator - Instructions

I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.

First I removed the 14.3 tons of freezer contents, closed the water valve, shut off the juice, and removed the freezer bins, the freezer door and the three screws that held the element in place. After bringing in 397 hand tools from my garage inventory, I loosened the unit and, after extensive evaluation, I finally disconnected the wiring connector from its freezer rear wall connector counterpart. You ain't gonna believe the rest of my story--of total ineptitude by an experienced fix-it-yourself dummy.

I searched the internet for a replacement ice maker and found it at partselect.com. I called Sears to ask if I could add my refrigerator to my existing appliance repair account. Sears said sure--it would cost me only one arm, three toes and one grandchild. I abruptly declined their magnanimous offer—I don’t give up my arms and toes so easily.

I visited the local Maytag repair parts and service retailer, who advised they didn't do parts anymore. Expecting their repair price would be greater than Sears, I resorted to partselect.com. I called them to be assured what I was buying was not mistakenly a 747 Landing Gear. On the afternoon (West Coast) of 4/28/10, I ordered (via internet) one PS21215123 Ice Maker Assy. Much to my pleasant surprise, it arrived via FedEX on 4/30/10 (no freight charges to me).

My repair/replacement efforts were hampered by the effects of my right rotator cuff surgery a few months before and major left wrist surgery two months ago to remove fractured bones and torn ligaments.

Undaunted by my physical handicaps, I forged forward. After re-installing the unit, I turned the water supply and electricity back on. It was graveyard dead. I wisely then bought two bags of ice as an interim solution to the severe needs of my wife and me for our daily chilled evening cocktails. I removed the unit, checked it out and re-installed it. I bought two more bags of ice. All the while, I turned the water and electricity off and on as required by reasonable safety standards. High tediousness!

Several more home maintenance tasks then arose for Sergeant Super Fixer, but I returned to the ice maker problem on 4/8/10. Last chance--remove the device and insure there was no frozen ice in the inlet tube--or call the local partsless repairman. No ice found, but I did learn the wiring connector to the unit was awry--no contact! While explaining that to my wife, I realized the two upper mounting screws were intended to be partially installed into the freezer wall to accommodate the unit's slotted mounting holes! Then, tighten the screws. Oh my God! During my 143 installations and removals, I had installed those screws blindly--using the (handicapped) skills of my right and left hands without any benefit of direct eyesight.

I returned to my challenging project this morning (4/9/10), fully utilizing all the expertise I had gained yesterday. Fifteen minutes of amusing effort! Turn on the juice! Turn on the water!Two hours later, ice cubes were dropping into the bin like rhinoceros bisquits in the jungle.

Hallelujah! I now am free for the next challenge!

HINT: Put a bed pillow (an old one, or your wife's) in the freezer compartment to soften the harshness of its cold metal on your back, if you use the "crawl in on your back" approach.

The ice maker was not getting water. I hotwired the water valve by switching the connectors for the water dispenser and ice maker water valves and water flowed into the icemaker when the water dispenser lever was pushed. I wronly assumed the water valve was good. I removed the icemaker and determined that the gear motor was not getting power in the position the icemaker had stopped.In this position, the thermostat determines when the motor gets power so I replaced the thermostat. The icemaker still would not get water! As it turns out, the water solenoid was sticking due to a deteriorated rubber washer which let the solenoid plunger get too far out of the magnetic field. I replaced the water solenoid assy and all is well. Don't get fooled by hotwiring the valve. If it isn't getting water, the solenoid probably is the culprit.

First of all, let me say that I'm a 50 year old single woman. If I can do this repair, anyone can! After unscrewing the back of the unit that houses the compressor, I found the relay overload switch which is attached to the compressor. I pulled the part off and discovered that it comes in one piece. The replacement part came in 3 pieces. I intially thought they sent the wrong part. After a little thinking outside of the box, I figured out that the replacement part was indeed the correct part and that it comes in 3 pieces instead of one. It would have taken 5 minutes to repair if I had realized this early on. Once replaced, the refrigerator/freezer was cooling within 10 min. I sent the Run Capacitor back after telephoning a customer service rep. She was so courteous and helpful! What a fabulous company. I highly recommend. I saved myself approx. $250.00 doing it myself.

Removed all parts and replaced defrost heater/thermostat and new clip then replaces Defrost board (new ones just snap in) and replaced all parts back and seems to be back to normal.
Thank you Parts Select

We just followed the instruction sheet that was included in the parts package. (instruction sheet has pictures) I just removed the 2 screws from the front and then disconnedted the element. unscrewed a couple more screws put on the new parts and reconnected the element put back the screws and it was done! I'm a single womand so me and my 23 yr old daughter did this project together. I ordered the parts early in the day and got them the next day. I only paid for 2-3 day shipping. I have ordered parts from Sears. They never have them in stock! The last order cost me $19.95 to ship. I waited more than 2 week for them to arrive. With Partselect the job was finished in 3 days!!

Replaced the compressor with the new one I purchased from you. Installed new parts and recharged unit. The refrigerator / freezer is working better than new. Thanks for the great deal on the compressor. It was here in 3 days. All the parts fit exactly and had no difficulty in the installation or startup. The directions for the wiring were a great help also. Thanks again.

Through experience I determined the problem was with the compressor trip switch. It's the small white piece that looks like a flat fuse.

The parts arrived in 3 working days. Instructions were included - very easy to understand. From start to finish I replaced the switch in about 15 minutes. Frig is now working perfectly.

3 pieces come along in the kit - however, all I needed was the switch, but for the price I changed out all three to assure compatibilty.

I also ordered the cover which was not needed.

A Happy Customer! {:-)

Quiet a simple repair. First I removed the ice maker bin and the plastic side panel on the right hand side. From there, I was able to remove the ICE ENCLOSURE . It unhooks. Next I removed the ICE DESPENSOR ENGAGEMENT YOKE. It has reverse threads so be careful. Next I removed the ICE AUGER MOTOR. Its located at the back of the ICE ENCLOSURE and held in place by 4 phillips screws. You also need to remove the SOLENOID YOKE ASSEMBLY which is located just to the left of the ICE AUGER MOTOR. It unscrews with 2 phillips screws. Next I reassembled the ICE AUGER MOTOR and SOLENOID YOKE ASSEMBLY to the new ICE ENCLOSURE. Then I reinstalled the ENGAGEMENT YOKE and snapped the unit back in place.

After removing all shelves, I removed the 2 screws holding the 2 panels in front of the evaporator and heater. The heater is located at the bottom of the evaporator coils and is held on by a simple wire clip. After removing the heater and thermostat, is very easy to replace the new unit and reconnect the wire harness.

Perhaps a helpful hint:

When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection.
I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.

LG

The tiny piece of plastic that holds the wire that shuts off the icemaker, broke early on with our fridge (after just a few months.) We superglued it, but last week it bit the dust for good.

Once I got this part, I removed the freezer door and trays, and pulled the icemaker out by removing 3 flathead screws and unplugging the cables. Laying in the freezer on the floor was a bit unconfortable, but not too bad.

Then I inspected the icemaker. There was no obvious way to remove the part without disassembling the front of the unit (where the motor is) to release the spindle and free the part, so I did that - 3 or 4 nuts was all that held it together. Once that was out, I removed the spindle, swapped out the part, and put it all back together and back in the freezer. Plugged it in and waited.

It took a while to start making ice. Like 5 hours. Now it's going pretty slow (much slower than before.) Haven't had time to look into it, but my suspicion is the rubber hose that feeds water into the icemaker is blocked with ice or kinked. In any case, we have ice now (but not a lot), and the unit shuts itself off properly. However, we went from having too much ice (thing never shut off) to too little (thing makes ice too slow), so I need to shoot for somewhere in the middle ;)

removed all 6 screws in back of fridge. located the condenser the relay was a white like circut to the left of the unit. The entire pience comes off easy using a flat screw driver to pry it off the pins.
The replacement came in 2 pieces insted of 1.
I replaced the relay and then the overload reconnected the wire harness back the way it was before. The new relay has a larger connector prong for the live wire so the kit comes with a jumper wire so the original wire harness can be used without splitting the cabel made the repair very easy. Also the new capacitor is bigger and better so I replaced that as well. The capacitor makes sure the relay gets stable current so its good to have a working one.

I first dropped the Cover Assy, which covers lites and controls, this was done by pulling it forward and it drops down, did not remove top shelf so It was a bit difficult to tilt cover assy. for removal. There is a srew located close to filter assy. in back use nut driver 1/4"located to remove this screw, there are then 2 screws located to the rear and side of light holders, both phillips head, the one on the left side is a bit tricky to remove but I use a thin bladed scredriver, Next there are 2 screws located on both ends od the slides that control temp, both again removed witn1/4 " nut driver, the whole upper assy drops down and forward the Adeptive Defrost assy is located in the back right corner of this assy, unplug the wires and unit snaps out, I foud it easier to pop off top cover of new unit so I could see connector assy when I reattached the wires, then replaced the top assy and snapped new unit it place, Reassymbly was reverse of removal, before placing cover assy back in place I replaced both lamps as 1 was out .

First I removed the screws from the front of the ice bin which freed up the drive mechanism. I then removed the drice ring and replaced it with the part from Parts Select and then replaced the screws on the front. A very simple procedure.
The chill department door was an easy snap in replacement..

I would like to add that I was very pleased with Parts Select. Locating the parts I needed was very easy and I received them the next day. When The door first broke I was told I would have to replace
the whole assembly which I was not willing to do
at a quoted price of about $350.00. Needless to say I was very happy to locate Parts Select and was very pleased with everything. I have since told family and friends about Parts Select.