JSD2695KES Jenn-Air Refrigerator - Instructions

replaced ice maker, followed the on line video instructions and it was the easied repair i've ever made it took less then 15 minutes

The replacement ice maker was exactly the same size and model. All the mounting screws lined up and install was snap. The website parts description was very good and helpful. We now have ice cubes with no over flowing glacier in the ice tray.

As per instructions to replace filter

I used a knife blade to slip under the edge of old switch to pray it out of the hole it was inserted into, switched the wires and replaced the new switch into the same hole. It took about five minutes!

Unlike what the online video showed, my bottom freezer French door refrigerator didn't use hooks to secure the icemaker in place. Instead, it used three tabs with screws to secure it in place. I could see two of them, but not the third one. After removing two screws and realizing that the icemaker was still pretty well secured, I felt around and found the third screw (at the top, right behind the front of the icemaker). Once I got that out, the replacement went easily, as shown on the video. That third screw was a little challenging to put back, but after a few tries I got it in. The icemaker is now making ice like a champ! Good work PartSelect! And the part came quickly, as advertised.

The problem had occurred twice before and the metal auger could no longer be reliably forced back into alignment with its end cap. It was time for a replacement. I opted to replace the entire auger assembly including the crusher blade - a total of three individual parts in this assembly. With the Amana model and serial number in hand, I logged into PartSelect and found the ice maker part(s) in the fridge schematic diagram. I ordered the assembly which arrived early. It is easy to disassemble. Remove the ice drawer from the freezer, minus the ice, and place it upside down on a work surface. You only have to remove four screws; the two on the front bottom of the ice drawer and the two screws holding the little L-shaped brackets that receive those two bottom screws. Tip: To avoid any confusion during reassembly, just take a picture of each step of your disassembly. You can do it Noonan.

Easy to replace part - remove panel at the bottom rear of the appliance, unplug from the compressor and connect the new relay. Unfortunately, it was not the relay on my appliance -- looks like the compressor has gone out -- new fridge for me

First pulled the Ice tray out of the freezer, Pulled the cord for the power to the refrig. Removed 3-Srews with the nut driver and disconnected the Power Supply to the Ice maker. Removed it from the freezer and started to remove the Bail and install the bail in the new Ice maker. Remove the cover from the side of the old ice maker and install it on the new ice maker. Put it back in the Refrig and connected the power cord and installed the 3-screws and reinstalled the Ice Tray and 30 mins. later it started making ice. Thanks for the Youtube Video it helped a lot to take the pressure off of doing it your self.

Pried out the old switch with small screwdriver, popped in the new one and tah-dah!! ..the light came on. While I was at it, I cleaned out the freezer :). I cannot begin to imagine what a repairman would have charged for this.

Received the hinge and it took only minutes to hang the refrigerator door.

Ordered the correct replacement part (Icemaker Auger and Crusher Blade Assembly) as found here at PartSelect.com. Part was delivered within two days. Removed two screws to remove the old assembly; inserted new assembly, replaced the screws and problem fixed. Couldn't be easier.

Replaced water filter head. Very easy to do. Make sure that you also have a bucket so that you don't spill water everywhere when you disconnect the water line from the fridge.

Removed old auger unit by removing two screws - installed new auger unit by replacing the two screws. Easy schmeasy!

1.Lift out the ice bucket. 2.Remove two screws at bottom. 3. Remove front (made up from parts 20 and 21 in diagram by lifting the plastic flanges at the bottom and sliding it off upwards. Fingers were adequate to lift the flanges. 4. Remove the mechanism. It comes right out. 5. Slide the mechanism into the new bucket. 6. Put the front onto the new bucket by sliding down and lifting the flanges over the ridge at the bottom of the bucket. 7. Put the two screws in at the bottom. 8. Slide the bucket back into the freezer. This was the easiest repair I have ever done.

Based on comments I read at this web site, I first ordered the water valve; that did not fix the problem. Replacing the icemaker did fix the problem. It was easy to replace. Contrary to the instructional video, I couldn't simply tilt out the icemaker at the bottom after removing the lower screww; I had to loosed the two top screws as well. The leak was caused the coating on the icemaker being cracked and peeling.