JSD2695KES Jenn-Air Refrigerator - Instructions

I pulled the frige out, took off the cover from the bottom with a nut driver. Took off the safety clip then pulled the plug out from the relay then the relay came out. Replaced the part and reinstalled the same way. This was really easy and fast.

I wasn't sure about the part I needed so I called the service number, they help me decide on the correct parts for my unit. This was the easiest repair I've ever done. One hex head screw and one clip in electrical connection and we were done. It took less than 5 minutes and now it works like new, no more leaking water and plenty of ice.

I snapped the cover plate to the filter open. Pulled the filter down and twisted counter clock wise to take filter out. I installed the new filter in by inserting the filter and tuning clock wise to secure the filter. I flushed the water for about two minutes and then allowed it to be put back into service.

Undid 4-5 hexhead screws, removed plate, disconnected old valve hoses and wire connectors and replaced valve. Save a ton of money!!

I simply followed the online instructions. Easiest repair job I have done. Once installed, which took about ten minutes, it was producing ice in less than two hours and is performing as it should. Had my frig not been a bottom freezer the installation would have taken less than five minutes. And to let everyone know, the on line instructions came in very handy during the removal process. Many thanks.

I ordered the replacement parts on line and received it a few days later. Thought I'd wait till the weekend to install the new parts. I expected it to take longer so I waited. Boy was I wrong. The hardest part was unloading the top shelf of the freezer. And it took longer to go get the nutdriver. I should have put it in immediately. Thanks for the instructional video. Works like a dream NO LEAKS. Will use your services on other parts as needed. Don from Pittsubrgh, PA.

Followed video advice

Removed malfunctioning icemaker and discovered that inlet water line was frozen. Thawed line using hairdryer and problem resolved. Returned new icemaker to PartSelect they promptly credited my credit card account. Problem solved.

I discovered that the water inlet was freezing, then the incoming water would run into the tray. I watched the video, then removed the ice maker. I discovered the the top two screwed just had to be loosened, not removed. I removed the bottom screw and move the ice maker to the side to disconnect the wiring harness. I found it to hard to disconnect. The pinch clips did not depress as they were supposed to, but the finally release. I did the replace without unplugging the refrigerator and it went fine. Took less than 15 minutes.

I removed and inspected the old unit and found the tray coating was flaking off. I ordered the new ice maker on line, One screw and rotate unit counter clockwise about 10 degrees unlocked it from the two snap in mounts. then unplugged the wire harness and it was free. Had to put the short wire harness on new unit, reverse removal steps and it is completed and working fine.

Replaced the ice maker. I have a 3 door refrig. It has a bottom drawer freezer. Remove the freezer door to make this much simpler. On my unit, the ice maker is installed with three screws, rather than one and two clips. Check before you try to pull it out. You should unplug the old ice maker from the refrig, leaving the wires on the old ice maker. It's much easier to remove the old wiring harness from the old ice maker once you've removed the front plastic cover on the unit. Both plugs on the harness have clips on them to prevent accidental disconnections. Be sure to find and press the clip releases before you pull on the wires. Nut driver makes this job easier than screw driver. You only need one size for all screws. I used the old ice maker bottom mounting clip rather than trying to bend the new one to shape. Much easier. My old ice maker had an extra wiring clip, which I moved to the new unit before the install. There is one wiring clip to hold the temperature probe, and another just to keep the wires neat. Letting the old ice maker front plastic cover warm up a bit before you try to pry it off for reuse is a good idea. Less chance of cracking. Two hours after the install, I had new ice in the ice bin.

Opened the refrigerator door, pulled down the filter cover, twisted the old one out and removed it. Placed the new one in - twisted it into place, replaced the cover and closed the door. It is working great!!

The icemaker in my Maytag refrigerator was having a few problems. First, a small leak developed in the ice cube tray, allowing water to drip into the ice bucket. This of course caused the ice to become one solid mass, totally inappropriate for a gin and tonic. After a couple of months of this, it stopped working altogether. On to the internet I went, and discovered how easy this repair actually was. One nut to remove, one to put it back in. The installation video was very helpful. I did have a concern at first because the icemaker did not start making ice rights away. I thought it might be a defective unit. It took about 12 hours to get the first batch and it has been happily cranking out the ice since! Ed in upstate New York.

Exactly like the instructions in this website. Unplug the refrigerator, remove 2 screws from the door ice/water dispenser, remove cables from solenoid, remove ice chute Seal, ice chute door insulation, ice chute door, remove hinge-door and spring, replace in reverse order and in 15 minutes the problem was solved.

I took the glass off the old shelf. I then removed the crisper tray following the old crisper shelf. I put hte new shelf in, which fit perfectly, and replaced the glass and tray. It was super painless and took no time at all....all within 5 mins.