JRSD224W (7N07A) Jenn-Air Refrigerator - Instructions

After going to manufacturer's web site and customer service phone, was unable to locate the correct switch in the dispenser area on the door. Your web site had the picture of the switch and it was right on and in stock. Shipping was quick and inexpensive. Repair went quick and all is well.

took nut driver and removed screw holding valve to refrigerator removed valve. Swapped water lines from old valve to new valve,plugged in selonoid wire harness to new valve reattached the water valve to referigerator and turned water on and forgot it. No leaks,ice and water in 24 hrs.

removed part., got number, went online,found part, ordered part, paid for part, replaced part.
works great. !

Removed power, removed the ice maker being held with three screws. Replaced with old unit. This box was so old that I robbed parts from the old and placed them on the new unit. Mkes ice very good.

I pulled the drive ring off of the icemaker and replaced it with the new part. Saved a $150 service call plus cost of part. It cost me a little over $11.00 and a repairman probably would have charged $30.

Very slowly, had no clue what I was doing. Instructions were great, and even I got the job done.

Just took old ice tray out and put new one right in place in less than 30 seconds. I am very pleased with how fast the tray arrived after being ordered. if only everything ordered could be made this simple. You are a great company to deal with.

After trying to clean and use chemicles to remove residue, I found that it would not work. Ice would build up in tray causing an overflow in the fill process. this would freeze cubes in tray below causing dispenser not to work properly, New tray seemed to solve the problem. Removed old and installed new

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve

had to saw off the shaft to get the yoke off and tap the holes for the 8/32 screws. all holes should have been tapped by the factory. Other than these problems, everything else went pretty good.

I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.

Removed all screws on back and 4 on front. That part is easy IF you have a Torx of the right size. Slip out the ice bin a bit and replace the drive ring. Reassembly is a bit harder since some internal shift can occur -- rotate or tilt the whole assembly to get two -- I think -- screws started. No need to over tighten screws; snug is good enough.

I removed the 2 crisper drawers and the glass shelf directly above the Pantry Drawer. Removed the Pantry Drawer and Pantry Drawer cover so you have easy access to the Right-Hand End Cap. On the right-hand End Cap, there are 2 screws which hold the End Cap in place, use a 1/4 inch driver to unscrew the screws from the front of the cabinet on the End Cap and half-way in of the cabinet, leave the screws in their holes in the End Cap. Lift gently to get off a small plastic pin, and move the End Cap away from the Cabinet. You don't need to completely pull the End Cap out of the cabinet, it'll move more like a door opening. Place 2 washers on each screw and gently put the End Cap back into place, being careful NOT to jostle too much so the washers don't fall off the screws. You will need to gently lift the End Cap back in to place over the plastic pin. Hand-tighten the screws back into place with the 1/4 in driver. Remount the Pantry Drawer on the sliders. When you go to install the Pantry Drawer Cover, you will need to gently push on one of the pins to get the cover back into place. Put glass and crisper drawers back into place.

Test by gently pulling on the Pantry Drawer. If properly mounted, the pins will extend fully into the Cover and will keep it secure when opening the Pantry Drawer.

I switched the ring and still had the same problem. What caused the Drive ring to crack was the Ice maker drive was cracked also, when it filled with water it would tip. The ice was not freezing completely and would cause the ice to build up and the auger was froze with ice or a big piece of ice would jam it. So I replaced the Ice Tray, it is working like new. I have to buy another ice tray as inventory, although I know inventory is bad but I never agreed with that theory.

Had to cut the old part off with dremel then just install new part and put back in refrigerator. It is a good thing to know that the Yoke is a left threaded. Thanks James from Pineville.