Enter the code TAKE10OFF at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on May 28 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Plastic cover had quarter size hole burned
Use a butter knife to pop small plastic pin out and turn to remove. Used the metal pinwheel from old one and placed it back up in the microwave. Never heard of this being possible, but it seems to happen per the website and many other comments.
No heat. No unusual noise. Appers to function other than no heat
Multimeter checked/confirmed switches, sensors, and fuse first. All good. High power diode was bad - Replaced. Still no heat but now loud "MMMMM" noise when running. This means either the capacitor is also bad and/or magnetron.
Used large screw driver to release the panel on inside of door. This revealed the two screws that held the handle. Using a Phillips screw driver I removed the door handle and installed the new one. Snapped the inner panel back in place. Job done. Simple.
removed cover over motor blew it out of leaves and dust. Removes 4 screws and removed piece ordered. The coil was rusted and not connecting. Changed oiece its working again
Turntable Stopped Working/Display Timer Would Countdown But Not Heat
With this model, you must remove the outer covering. Don't try to access the display unit from the front like I've seen in some other GE microwave videos. After removing the outer covering, the switches are easy to replace. They are very visible and easy to get to without taking any other parts off. You will see the door switches just behind the display board. Remove the switch and then remove the connecting wires to ensure you don't inadvertently brake a wire. You will need a tamper resistant star bit to remove 3 or 4 screws from the back panel. All other screws are philips head. I went ahead and replaced both switches (yes...there are two of them) and works like a charm. I saved an $800 microwave for less than $60 and know what to do if it happens again. Appears to be a common problem on this model. Thanks for others making a post...It saved me time and money reading others remarks. Good luck!
Microwave not turning on. All other functions operate
DISCONNECT THE POWER CORD and discharge the capacitor Leave unplugged overnight Remove vent grille by removing the 2 philips screws Remove the LED panel by removing 1 phillips screw Disconnect all connectors that plug into back of the LED board completely Remove the wires from the switches (3) at the inside edge of the microwave door Gently remove each switch housing and test all three switches for continuity Carefully replace non-functioning switches and reassemble the panel GOOD LUCK
Glass Turntable not rotating when microwave oven ON
Turntable shaft was worn and out of shape likely due to heat. Simply remove rotating glass and damaged plastic shaft underneath. Replace with new shaft.
This repai me couldn’t have been simpler! I noticed that the stirrer fan cover on our microwave had melted areas. My husband suggested we just buy a new microwave. As the handywoman of the family, I searched online to see if it was a fix that I could handle. I ordered a part for less than $20 and fixed it in about 30 seconds! All I had to do was pop out the plastic screw, put the fan in the new cover, and pop it back into place!
I opened it up, found there is sparks on the diode when cooking, I replaced the diode first, still no heat, I found all the switches and thermal stats were normal, there is 120V AC input to the transformer, so I tried to make a good guess and bought a Magnetron from Partselect, after I installed the new Magnetron, there is heat and the microwave is working.
Googled problem, removed diode, checked with meter and it was open, ordered new diode, checked new diode and it read open, installed. Any way, it didn't work. Went and bought new microwave!!