Door fell off so removal of door was easy. Removed screws holding the door together to expose hinges. Removed old hinges that were 3 screws for each hinge. Placed new hinges and installed screws then put door halves back together installed screws and then finally replaced door onto the stove. Mission accomplished
1. Order correct light bulb for unit and have it with you before removing old lightbulb. My Microwave is built into cabinet. 2. Disconnect power (Either turn breaker off or unplug unit from wall) 3. Remove face cover on cabinet. (4 Phillips head screws) I was able to reach in the opening in the cabinet and unplug from the wall. 4. Remove Phillip head screws holding microwave in cabinet. 5. Remove microwave from cabinet. 6. Remove Phillip head screws and torx screws holding outside cover on the back of unit and the side (1 on right side) and then remove cover. Light bulb is on the top front right side. 7. Remove 1 philip head screw holding light bulb and unplug quick connector wires. 8. Plug quick connector into new light bulb same way it came out and place new light bulb in place and put the 1 philips head screw holding it back in place. 9. Put cover back on and all the screws. Temporary plug the unit in to test light bulb works before securing it back into cabinet. 10. Reverse order 5,4,Plug unit in wall before putting the face back on. Done.
Watched a you tube video prior to installing new switch. Followed the video which gave me confidence i was up to the task. After removing the touch pad I found my design was not exactly like the you tube model but I found the defective switch, replaced it and put the microwave back together. Works great. Again watch the videos
Required that i remove the built in frame and mounting. Required tamper proof socket to remove housing. I removed the old bulb and simply replaced and reverse installed the cabinet.
Oven door would not close all the way, light stays on.
First I removed the oven door - with door fully open pull the clips on the hinges all the way out, then close door as far as it will go and lift the door up and off the oven.
Then I removed the three screws on each side, that hold the oven to the wooden cabinet. I then slid the oven unit out from the cabinet about 6 inches, to gain access to the hinge receptacles.
I then removed the 2 screws that secure the receptables to the oven body, and replaced the receptacles.
I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane. It took less than an hour. Thanks for Your prompt service.
Rotated the hinge lock with a screwdriver, pulled door off hinge bracket, later door on table, removed screws to detach inner door frame from outer door. Three screws to remove each hinge. Very easy.
After watching a you tube video or two, I easily detached the oven door. One of the hinges was jammed, and upon releasing it with a screwdriver, it snapped open and gashed my thumb. This as entirely my fault, I did not realize how much force was held in the spring.... You must remove the bottom frame piece and inside door pan to get to the hinges. All Phillips head screws, and all the same size. Once these are removed the hinges are easily removed with 3 Phillips head screws. While l was this far into it I removed the two layers of glass to clean them on both sides. This requires a small nut driver to remove the channels holding the glass. There are three layers of glass to clean on both sides, quite dirty and brown. Reassembled the whole thing. The door assembly popped right back in, and now functions like new. You can actually see into the oven, without opening the door!
Pulled the double wall oven out about five inches and install replacement brackets on both sides. Reinstalled oven doors and slide ovens back. Piece of cake— the lower oven door closes better than when oven was installed 13 years ago. Believe I had a bracket problem from day one!
This was easy to replace. I removed the oven door for easier access to the back of the oven. Removed two Phillips head screws that hold the burner element and disconnected the two wires on the burner element. I could have left the wires connected, but it was easier to extract the sensor with it out of the way. The only difficulty was fishing the sensor connector out through the hole. After that, easy peezy.
Removed the door and the screws that secured the oven to the cabinet. Pulled the oven out about four inches to provide access to the hinge brackets. Removed two screws on each bracket and removed the brackets. Reversed the process and all was well. Works like new.
Our contractor had buggered up the hinges on our oven door and they needed to be replaced.
First, I thought we were in big trouble as our oven is in our house on a small island in the Bahamas. We thought our choices were to either take the door back to the US have it repaired and then bring it back to the island (which could take weeks) or fly a repairman in at a cost of about $1500. By my good fortune, I found Parts Select when I did a google search for Jenair Ovens and the website walked me through how to find and order the part. It was FedEx'd and within 48 hours our door was back on and we had an oven again! Thanks so much!