Models > JMV8196AAW > Instructions

JMV8196AAW - Instructions

All Instructions for the JMV8196AAW
91 - 101 of 101
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Turntable Roller Guide Turned, But Glass Plate Did Not Turn. White Rollers Became Flat.
Just place it in the slot. . . . . 5 Seconds,,,no problem
Parts Used:
Turntable Roller Guide
  • Rodger from Somerset, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Turn table stopped working.
The turn table motor stopped turning ,but we never turned the off button off on the microwave and kept using it ,so it shorted to the outlet neutral (white) wire at the circuit breaker fuse panel , the wire burnt off. I cut the wire re-installed it in a good buss connector.That restored power back to the outlet.** So now to replace bad Turn-Motor: Using phillip screw driver remove (bottom)filter/light panel- 10 screws, unplug lights and motor connectors, lower panel out of the way ,remove 2 screws from motor and replace motor. Install in reverse order. (Fast Fix)**Note:If you had other problems like I did consult with a professional electrician.
Parts Used:
MOTOR-TURN
  • RONALD from STOCKTON, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Bulb burned out
You had alerted that it was imperative to unplug unit before starting to remove defective bulb. As described, there was silicon on bulb and socket and bulb broke upon my attempt to remove. Had to use needle nose pliers to get metal base of old bulb from socket, then all went well.
Parts Used:
Light Bulb - 40W
  • Lester from Mesquite, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Two of three roller arms broke under microwave round glass tray.
Lifted old one out, put new one in. No problem.
Parts Used:
Turntable Roller Guide
  • Cuthbert from Valparaiso, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Microwave would not cook
All the electrics worked on Amana microwave EXCEPT for the cooking function. Inspected the control board and found the upper switch on the door interlock was burnt. Installed new switch in minutes and everything now works fine. Unfortunately, had to purchase expensive two switch "kit" although only one switch was kaput. PartsSelect mailing was SUPER fast. Thanks for looking, Scott
Parts Used:
Door Interlock Switch Kit
  • Scott from Mickleton, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Turntable roller guide broke
Pulled out broken roller guide, replaced it with new one. It was just that easy.
Parts Used:
Turntable Roller Guide
  • Michael from Englewood, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Microwave failed to head and light, fan, and turntable failed to come on.
Problem was due to a faulty door switch. Replaced with a new switch and the microwave now works fine! Only thing that was tricky was that LG uses the hex screws with a peg in the middle to keep the microwave cover on. Had to use a small screwdriver and pliers (on the screwdriver) to unscrew the screws.
Parts Used:
Micro Switch
  • Robert from Cedar Park, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Needed a new bulb under the microwave.
After unplugging the microwave and removing the screw, I removed the old bulb and put in the new one!! I made sure it was in securely and the difference in the light was awesome! I use this light when I bake bread and let it rise inside the microwave, but DO NOT turn it on. The heat from this light helps the bread to rise properly!!
Parts Used:
Light Bulb - 120V 25W
  • Norma from Unionville, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
burnt out light bulb
The problem I have with changing the bulb is my microwave is an overhead one and therefore I cannot tip it on its side to easily replace the bulb. I have to drop the lid down and carefully install the new bulb from underneath.
Parts Used:
Light Bulb - 40W
  • Shirley from Londonderry, NH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burn't out bulb.
Removed the glass cover and replaced the bulb. Very simple.
Parts Used:
Light Bulb - 40W
  • Carter from McCordsville, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
turntable platform broke
Dropped in the new one. Took about 30 seconds.
Parts Used:
Turntable Roller Guide
  • Rex from Mount Sidney, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JMV8196AAW
91 - 101 of 101
Back to Top