Models > JMC5200AAW > Instructions

JMC5200AAW Jenn-Air Microwave - Instructions

All installation instructions for JMC5200AAW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JMC5200AAW
1-15 of 58
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Microwave worked intermittently depending on how door was closed

  • Customer: Robert from Bainbridge Island WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 29 of 35 people found this instruction helpful
Remove top grille (2 screws), undo control panel (1 screw). Tilt down control panel, switches are on the left. There are actually three switches that are involved with the door, two horizontally mounted, one vertically mounted. This would be an EASY REPAIR, but it took me a while to figure out which of the three switches was bad, and also took a while to figure out that there is a plastic rod that inserts through the hole in the switch body. Once i figured this out went like a breeze. Lower horizontal switch was the bad one, but since the kit came with two switches i went ahead and replaced the upper horizontal one as well. IT appears that the horizontal switches are probably more likely to fail than the vertical switch based on the position of the switch and force angles. Works great now!

loud buzzing noise

  • Customer: Sandra from coto de caza CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 29 of 51 people found this instruction helpful
The repair went well...I am so glad that I read this info before buying a new microwave....it saved me lots of money. I did have a repair man come and look at it and he told me to buy a new one but it cost alot of money when it wasn't necessary. I did the repair and I was very proud of myself.
Three men watched a woman fix this and it was no problem...they were impressed also....

Broken tray ring for rotation of dish.

  • Customer: Michael from Sewanee TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 13 of 14 people found this instruction helpful
Used needle nose to pull off piece of old ring. Layed in new one.

Turntable not moving, intermittent "grinding sound"

  • Customer: Annika from Rancho Cucamonga CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 9 people found this instruction helpful
The microwave is installed above my gas range, and has a sheet that holds the vent screens and light bulb cover. I removed 3 screws holding this sheet in place at the front edge closest to me. The edge furthest from me (closest to the wall) had grooves that the sheet slid into. I could not set the sheet down on the counter as the electrical wire was anchored to the sheet and too short to reach the counter below. I used some jars to prop up the removed sheet so that there would not be any strain on the electrical wires. The wires connected to the motor with a bracket that was removable by hand. The old motor was mounted with one screw and a small arm that slid into a groove at the bottom of the microwave. I installed the new motor with the screw. At first I missed the groove and it was kind of crooked. I immediately detected and corrected my error . I made sure the piece inside the microwave that turns the turntable was aligned on the motor shaft. I closed it up and was delighted to see my food turning again!
By the way, the microwave is actually an Ewave, made by MC Appliance Corp., the makers of Magic Chef. It came with the house in 1994.

BLOWN FUSE - PS1750182

  • Customer: John from Inverness FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
UNSCREWED THE COVER OF THE MICROWAVE REPLACED THE BLOWN FUSE WITH THE NEW FUSE, PLUGGED IN THE MICROWAVE AND TESTED ALL FUNCTIONS AND EVERYTHING WORKED FINE.

THX FOR QUICK DELIVERY.

Close the door on the microwave, punch in the # nothing happened

  • Customer: Robert S. from Stafford TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 13 people found this instruction helpful
I removed the unit from the wall. Took the cover off. Set the unit on its side. It revealed the working parts. Removed the old micro switches. Put in the new oness. Presto, it worked. Very easy for me.
The parts was delivered almost before my notice they were shipped.

Turn table in the Micro was broken due to the plastic 3 wheel mechanism that cracked. t

  • Customer: Cesa Lynn from Montgomery TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
I could just set the new whirly gig in the bottom hole of the micro and it worked. The new part was delivered in 24 hours of my order and hence fixed in 24 hours. Thanks so much Part Select

Turntable stopped working

  • Customer: Jeff from Cape Coral FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
I removed the old turntable motor from the microwave and replaced it with the new motor.

My turntable wouldn't turn

  • Customer: Yvette from Riverdale IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
I took the turntable roller guide, dropped it into the hole, put the plate back on the turntable roller guide; and voila!!! It worked!

no power at all

  • Customer: patricio from chicago IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 8 people found this instruction helpful
unscrew microwave's cover,test the fuse which is located at top rear left side, the fuse is inside a plastic tube,if the fuse is burnout,just replace it.

Old roller piece broken

  • Customer: Jack from Scottsboro, AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
Took out the old, put in the new.

Turntable Motor gears stripped

  • Customer: Matthew from Edmond OK
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Had a Trim Kit to remove, just 2 screws on the front to pull it out. Had to remove the tamperproof screws on the back (the outer shell is held on by them). I had to goto a local hardware store as nothing anywhere mentioned I needed this special tool (NOTE!!!!!!!) The bottom had normal phillips head screws. Note: I did not take the entire shell off, just bent it enough so the base plate could be pulled out. This exposed the motor, which strangely enough is NOT held in by any screws, just notches it slides in. Took the old motor out, came out VERY easily (only 1 plug to pull out). The new motors flange tab was bent a little bit so I had to use pliers to bend it back flat so it would fit in the notch on the bottom of the microwave (very easy). Overall A bit difficult due to special tool needed 9at least for me)

turntable stopped

  • Customer: doug from broadway VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
4 screws out and replace motor and 4 screws done.

Fan motor and magnetron did not come on, but every thing else did.

  • Customer: Dale from Chester CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
Problem would come and go. Found service schematic inside unit. Perform all the suggested tests. One possible solution was the primary interlock switch shown on the schematic and a check found the switch stuck. It would free up some times but would stick again in the open position. Ordered switch which was a simple plug in unit.

Needed to push door up to run appliance.

  • Customer: J Patrick from Baltimore MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 16 people found this instruction helpful
1. Removed cabinet screws (10-15?). 2. Removed cabinet. 3. Removed top interlock switch which actually was not defective. The press clip connection appeared as if it had been arcing for quite some time and the corrosion created resistance sufficient to prevent the current from getting through the switch. 4. Replaced switch anyway but broke plastic retaining clip despite every effort not to do so. Reset broken clip with super glue. 5. Reassembled cabinet and appliance is in good working condition.
All Instructions for the JMC5200AAW
1-15 of 58