JGR8890ADP Jenn-Air Range - Instructions

Pulled the oven away from wall to access rear of oven. Disconnect electric plug from duplex outlet, turn off gas supply ball valve. Removed two screws that retain sensor on inside of oven. Disconnected two prong sensor connector at rear of oven. Tied a length of string to sensor connector wires. Pulled old sensor out through front of oven. Use the string to tie onto new sensor connector wires and pull new sensor into place from rear of oven. Retain sensor with two screws. At back of oven, used connector jumper supplied with part package to make connection to existing connector.

I ordered the part one afternoon. It arrived before noon the next day. Then I simply removed the old seal (with about 2 dozen spring clips). Inserted the new part by carefully inserting the new seal into its corresponding hole at each end and then worked my way around the seal while inserting each attached spring clip into its corresponding hole.

place new ones in by hand. the new ones fit too loose and if not carefull they will fall out.

Look in the oven. On the upper left corner is the sensor. Remove two screws. Gently pull the wire and connector through the hole and insulation. Disconnect old sensor, replace new. Gently push the connection through, then finish pulling through from behind the stove. Replace the screws inside the oven. Done.

easy-peasy remove small panel on back
disconnect in the back of range-oven "orange wire"
unscrew igniter from burner inside oven
remove and replace with new one
slide wire thru hole in back of oven
reconnect---u r done
dave

Remove door, racks, unplug, remove lower burner cover two screws, the burner tube deflector pan two wingnuts, the burner tube. With igniter attached, remove back of range 4 screws to expose connector to igniter, unplug then remove burner tube, then igniter, replace igniter feed through back of oven wall and reconnect igniter reverse process and its done

Purchased 2 piece broiler pan from this site

My wife called a service company and was told that a tech would have to inspect the stove.
service charge 60.00 After inspection the parts would be orderd and a 200 fee for labor plus the parts would be charged at the completeion of the job. 2 weeks for part. I found you on the net orderd the glass. got it in 2 days and I completed the repair in 20 mins. Cost 89.00

. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) pushed wires back in and secured sensor

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then conected the new element and replaced te two screws. Turned on the oven & works fine.
Very Easy!

I must admit that I did not do this. A neighbor who has electical experience did the job.

The screws that hold the ignitors were too corroded to reuse. It required drilling new holes and taping threads. If self-taping screws were included it would be easier to replace.

The switch was much easier to replace with flare nut wrenches.

I removed the door from the oven and set it on towel on the table, and started the repair of the door. I removed the screws one at a time, and one layer at a time. Becareful you need to take the whole door apart, and remember how it goes bact together. In the end it was worth it. The hardest part was getting the right part. I thought I could order the whole door, and found out after several calls they don't sell the whole door. Part Select both times I put in my order had the parts at my door within 2 to 3 days. I also had to return one of the parts and within 2 to 3 days the part was credited to my account

Clearly, the oven gasket was not the cause of the problem.
The hinge replacements did not fix the problem. I think the problem was that the hinge's mating part inside the door had been deformed, perhaps by leaning on the door when fully opened. I compensated for that by placing two stacked magnets near the upper hinge mounting screw hole on the inside of the oven body. (0.75" screws , 8-24 or metric equiv., needed for the upper screw location.) This gave the hinge about 15 degrees of additional door tilting force. In addition, I added 6 ceramic magnets across the top of the door mating surface, kudos to that website. Now it pulls fully flush with the magnets.
Ceramic magnets are good to 400+ degrees and they come in boxes of 120 for $12.00.
I only had one oven as a sample, but I could see what I thought was deformation on the inside of the oven door where the hinges are inserted. In this case, I think that makes (only) hinge replacement futile.
Sorry if this solution does not fit your marketing desire, but I did leave the new hinges installed.

I removed the two screws that attach the sensor to the oven wall. Then removed to more screws in the back of the oven and took off the rear cover, diconnected the sensor connector and installed the new sensor.

After reading some of the repair stories, I was hesitant about doing this task. It was really very simple, I just removed the screws from the back of the stove, and removed the old element. I then replaced it with the new one and replaced the back cover. This whole task from start to finish took 10 minutes. The oven heats perfectly now just like a new oven.