JGR8875RDB Jenn-Air Range - Instructions

bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!

I tried to take it out from the inside as the vidio shows. But it would not come out far enough. I pulled out the stove and removed back sheet metal panel. Unpluged the electric, Unhooked the temp sensor,pulled it out from the oven side. Put the new one through the hole,and rehooked it up. And got to clean up the dust and my missing oatmeal I spilled a while back. Turned it on. Checked it with a spare temp gage. Works so far.

The website helped me to troubleshoot and identify my issue. They had a complete database to find my part and some instructions to how to install it.The repair was easy: 2 screws to remove at the bottom of the inside oven to remove the large plate. Then 2 more screws to remove the ignitor. Now to unplug the ignitor, I really had to access the back of the stove. i saw videos of people doing this from the front under the stove (not moving it). In my case, for this model, I had to move the stove to the "middle of the room", to access the back. Then 2 more screws to remove a small plate where I could see the cable to unplug.It was advised to close the gas faucet, and unplug the stove. I only unplugged the electricity, and it was fine. Then I tested the repair before I put back the large plate at the bottom of the oven.My only issue was the isolation "tube" going around the 2 wires ad connected to the new ignitor. I had them on my previous model, but not on the new model. So I managed to put it back to cover/isolate the new wires. Then everything worked again.

I lifted the burner tray from stove turned it upside down then removed six small screws from side of cover pan then I removed the cover then I removed the screws from the back of the old burners and igniter.Then I turned the old burner counter clockwise and it lifted out easly. the igniter is removed with no problem. The new burner is put in place and turned clockwise to lock in place.Then replace then the gas tubes and igniter and igniter wire then put tray cover on.

I lifted up the bottom insert of the inside of my oven and then followed the instructions on this site. Originally I purchased the wrong igniter, so I would encourage you to look at yours and make sure you are buying the right part. I am a complete novice. Even with my purchase debacle, my oven was back up and running within 5 days (total cost was $60). Do this even if you are scared of a screwdriver. Just remember to turn off the gas first. Make sure you've turned off the gas by trying to light a burner (if your burners are otherwise working correctly). If it doesn't light, the gas is off and there is nothing to be afraid of. The igniter is far enough away from the gas pipe that I wasn't afraid of breaking it and once I saw how the oven was put together, I wasn't afraid of working on it. And, if you need to return anything, the return policy is awesome.

This oven is part of a stand-alone gas (propane) stove. It was purchased and installed in July, 2005. The igniter I ordered from PartSelect arrived as promised. But the connecter on the new igniter did not match the connecter on the old one. I had to either find an igniter with a compatible connecter or splice the old connecter to the new igniter; I chose to splice. Now, I'm not a real handyman, and I'm especially skittish around electricity. But I found two wire connecters (plastic tube-like things with metal interiors). I stripped about a 1/4-inch from all four wires and inserted them into the wire connecters, making sure the igniter was properly placed so the screw holes lined up. Then I used the crimper tool to crimp the wires together. I did a pull test to make sure the wires were secure, replace the now connected wires in their proper place and turned the oven on. It worked! On this particular stove, you'll need a screwdriver to remove the vent cover, exposing the igniter wires. Due to the gas connection in the back of the stove, you can only pull the stove out so far. So, there's not a lot of room to work in the back of this stove; that's why it took a lot longer to complete this job than the wiring inself. I'd say no more than fifteen minutes. Of course, if all the parts are compatible, even less. Good luck!

unplugged range turned gas valve to off position, removed screws holding igniter, and unpluged igniter. reinstalled igniter following the same steps in reverse. removed door gasket with pliers,reinstalled new gasket by pushing clips on gasket into holes around frame of oven.Saved a ton of money, Thanks Partselect!

I called the yellow pages repair man and he quoted me $450 to replace the igniter. I did it myself for $63 and it took 10 minuet's. I'm gonna get a T shirt that says "Mr Fix It" Next is the refrigerator door gaskets! Someone from part select had mentioned that to take the door off the oven you "just open the door a little and lift it off". that was a helpful hint because I would have been looking for screws for half a day!

First removed 3 screws from top of door and the 3 bottom screws. To remove hinges there are 2 screws on the bottom ends remove those and then there is 1 in the center of hinge remove slide out old hinges and install new ones.The hinges have to be in the extended position I then put the needle nose pliers on the top end of hinge because they kept snapping shut before it engaged with the receptacle I put on one side when it was in I released the plier and it hooked I then proceeded to the opposite side it shouldn't have taken so long once I used the locking plier I was done in 10 minutes.

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.