All Installation Instructions for General Electric Cooktop JGP970SEK2SS

Grate Foot had worn out

A rubber grate foot on my range top had worn out. I pulled the worn foot out and installed the new grate foot with no tools or accessories. Good as new! Now I don't have to worry about the grate scraping my range top and scratching the paint. I also ordered extras so I won't have to wait if another wears out.

Parts Used:

Grate Foot

Kathryn from Star City, AR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

24 of 30 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

After my housecleaner had been here, I noted that 2 of the little rubber feet were missing from the top grates.

I was pretty upset as the grate wobbled, so I went on line and looked for GE Profile parts. To my amazement, I found the little rubber feet quite easily, and within 2 days they were here at my home. I simply had to stick them in the holes; however, I noted that they did not fit real tight, so I removed them and shot a little glue on them, and they have been in place ever since. Thanks to you guys, I am a happy camper now!!!

Parts Used:

Grate Foot

Anne from Jacksonville, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

feet keep falling off

Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.

I do use silicone to help hold the foot but it still won't hold

Parts Used:

Grate Foot

Richard from Stratham, NH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner would not light because spark was skiping to ground elsewhere

First I removed two screws holding head in place and carefully lifted assembly up using flat screwdriver. I separated old igniter from feed wire with gentle pull. I reversed assembly after cleaning old gasket residue. torque screws back in place after cleaning with small ss wire brsh in dremel tool. Tighten in steps to firm light touch. I used new gashket and ignitor.

Parts Used:

Burner Gasket

David A from Spring, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Rubber Grate foot worn or missing.

Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.

Parts Used:

Grate Foot

Terry L from Puyallup, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Rubber grate foot failed

Cut off approx. 1/8" in length for correct fit.

Parts Used:

Grate Foot

Gary from HENDERSONVLLE, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

stainless steel burner knob on GE range became stripped. Know would wobble and not turn on burner.

Pulled old burner knob off and inserted new burner knob. Perfect match. Burner works perfectly. Glad you stock these parts for my GE appliance.

Parts Used:

Burner Knob

Martin from SANTA BARBARA, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The Grate foot is to big for the hole.

I had to drill the hole to a larger size to enable the foot to fit.

Parts Used:

Grate Foot

Harold from Broadalbin, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

very easy

there were no grate pads so it was easy to add them.

Parts Used:

Grate Foot

ROBERT from CYPRESS, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The selector knob inside is broken

The selector knob came as the original that fit execly easy.

Parts Used:

Selector Knob

Geertruida from LOMA LINDA, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The Grate Foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.

Nothing technical.

Parts Used:

Grate Foot

Chelagh from Fredericksburg, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Grate foot bdroke off allowing grate to scratch cooktop

Used scribe to remove grate foot plug still in grate inserted new foot.

Parts Used:

Grate Foot

John from Tijeras, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Leaking from front door

First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.

Parts Used:

Grate Foot