Models
>
JGP636AEV3AA
JGP636AEV3AA General Electric Cooktop - Overview
Sections of the JGP636AEV3AA
[Viewing 2 of 2]
Keep searches simple, eg. "belt" or "pump".
Surface Burner Spark Electrode
PartSelect #: PS231276
Manufacturer #: WB13K18
This part helps your burner ignite and produce flame.
$41.95
In Stock
Screw
PartSelect #: PS271689
Manufacturer #: WH2X930
This screw is sold individually.
$12.22
In Stock
Burner Bowl Seal
PartSelect #: PS244599
Manufacturer #: WB32M10
This gasket goes under the burner bowl to help protect the glass from high heat. Sold individually.
No Longer Available
Foam Rubber Tape
PartSelect #: PS11726663
Manufacturer #: WB02X26088
This is foam tape and it is usually used in conjunction with your range, specifically on the cooktop. Its purpose is to help seal the edges of the cook top to the counter top. Another of its functions...
$39.82
In Stock
Gas Pressure Regulator
PartSelect #: PS2337785
Manufacturer #: WB19T10078
This comes set from the manufacturer for Natural Gas. It also includes the conversion to Liquid Propane.
This valve automatically cuts off the flow of gas at a certain pressure.
$54.42
In Stock
Single Liquid Propane Orifice Spud - Medium Burner
PartSelect #: PS240769
Manufacturer #: WB28K145
Sold Individually. Order quantity needed.
No Longer Available
Ignition Spark Switch - Rear Burners
PartSelect #: PS236639
Manufacturer #: WB24K5083
$26.53
In Stock
Ignition Valve Switch - Front Burners
PartSelect #: PS236635
Manufacturer #: WB24K5078
$37.42
In Stock
Questions And Answers for JGP636AEV3AA
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the JGP636AEV3AA
[Viewing 2 of 2]Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Burner igniter needed to be replaced
Assumed the entire top of the range would have to be lifted off. Removed the three screws inside the top of the over door and then noticed the two screws holding the dish around the burner. They were tight and required WD-40 and then a sharp tap and came off.
Important: Notice the direction your old igniter is plugged into the w ... Read more ire. It is not clear and can go on either way.
Important: Notice the direction your old igniter is plugged into the w ... Read more ire. It is not clear and can go on either way.
Read less
Parts Used:
-
Thomas from Bloomsbury, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
37 of 63 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip pans needed to be replaced.
Simiple repair. Determined drip pan size (sm, med., lg.) removed 2 screws holding drip pan, placed gasket around new drip pan and installed. Repaired took less than 5 minutes.
Parts Used:
-
Steve from Broken Arrow, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
18 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacement cook-top, had natural gas orifices, needed propane
Three were simple screw out and replace with a nut driver. The warming burner had a smaller opeining which was too large for the nut driver. Had to remove shielding aroound it first. Simple, job. My mother did the last one.
Parts Used:
-
Aloha from Monterey, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
9 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!