Models
>
JGD3536WB00
JGD3536WB00 Jenn-Air Cooktop - Overview
Sections of the JGD3536WB00
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Burner Electrode
PartSelect #: PS11744318
Manufacturer #: WP74009336
This is a burner electrode for your oven, range, or stove. This part has a male spade. It helps your burner ignite by creating a spark, producing a flame, and lighting the surface burner. If your burn...
$41.57
In Stock
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.42
In Stock
X-Large Burner Head with Electrode
PartSelect #: PS2085280
Manufacturer #: 74007736
This is the burner head and electrode for your gas range. If your gas igniter glows but will not light, or if the element will not start or heat entirely, you may need to replace the burner head. This...
$81.10
In Stock
Large Burner Head
PartSelect #: PS2085279
Manufacturer #: 74007735
This part includes the spark igniter.
$85.54
In Stock
Grommet
PartSelect #: PS11744194
Manufacturer #: WP74007705
This part is the replacement grommet for your cooktop or range. It is made of black plastic and is approximately 1 ¼ inches in diameter. This part may also be known as the cooktop burner knob gasket, ...
$9.13
In Stock
Cooktop Downdraft Vent Grease Filter
PartSelect #: PS11750896
Manufacturer #: WPW10240990
The grease filter traps grease from the exhaust air.
$36.44
In Stock
Exhaust Vent Blower Wheel
PartSelect #: PS11757592
Manufacturer #: WPY707985
This exhaust vent blower wheel is almost seven inches in diameter, and just under four inches deep. It is made entirely of metal and is used with a range's venting system.
$92.66
In Stock
Stainless Steel Cleaner
PartSelect #: PS2360188
Manufacturer #: 31462A
Use this bottle of stainless steel cleaner and polish for any of your stainless steel appliances.
No Longer Available
Questions And Answers for JGD3536WB00
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the JGD3536WB00
[Viewing 3 of 3]Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ignitor stopped working on gas cooktop
As others reported, there are 2 torx screws that need to be removed so that the burner element can be removed. One came out with a little effort, the other one did not as it was corroded. After breaking a torx bit, a second torx bit succeeded in breaking off the screw head. This then required a drill to drill out the broken shaft and th
... Read more
en rethreading the screw hole. On to the ignitor replacement. The tiny screw holding the ignitor was corroded and would not come out. It too had to be drllled out and rethreaded. It was a 1/3" #4 screw with fine threads. Had to get it an appliance repair store as the local hardware places don't carry fine threaded screws. Finally got it all put back together after a week. My advice before ordering an ignitor is make sure you can take the current burner off the cooktop first to do the repair in the first place. BTW, the ignitor I ordered came quickly and was the correct part!
Read less
Parts Used:
-
Jeff from Lake Orion, MI
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers, Wrench set
83 of 86 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The ceramic insulator on the burner ignitor cracked & the spark shorted so that the burner would not ignite.
Firts I removed the 2 screws that held the burber in place. Then I lifted the burner up & disconnected the wire that connected to the ignitor. Then I removed the one screw that held the ignitor to the burner. I then reversed these steps, replacing the cracked ignitor with the new one, replaced the screw holding it to the burner, then reco
... Read more
nnected wire, returned the burner to the stove and replaced the two screws that held it. All Done!
Read less
Parts Used:
-
Loren from San Luis Obispo, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
31 of 33 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
electrode would not lite burner
Unscrewed burner head and replaced with new burnerhead and electrode. Just like new. Parts cost 128.00 including shipping. Very simple repair. Saved 200.00 in labor. Parts came within 36 hours. Super Fast.
Parts Used:
-
Joe from Saratoga Springs, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
22 of 27 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!