JFC2089HPY Jenn-Air Refrigerator - Instructions

Turned freez control off. unscrewed singl sheet metal screw, lift off unit, from 2 remain. screws, unplugged
elect connect. Pulled off sm water tube Rmd elect cable unit from old unit, installed on new unit.
Reinstalled elect connect, installed water tube,
Rehung unit on 2 sheet metal screws. Replaced the ice rail[with old one]Turned on freezr control. Had
cubes in 1hr, 4 min... Oh yes, took off old end
decor cover & slipped on new unit .. Greetings from
Hartland, Mi/USA

First I unplugged wiring harness from the inside of the freezer. Then removed two small bolts on top side and one on the bottom. Then took it out of the freezer. Then unplugged the wiring harness from the ice maker. Then plugged it into the new ice maker. Then reinstalled it back into the freezer with the three bolts.Then plugged it back in.

took the screws & nuts out, removed the piece and replaced the broken piece with the new piece that was ordered.

I found your website with the step by step video on how to replace the ice maker on my refrigerator. It looked really simple, so I ordered the part from you and it was here in 2 days. It absolutely took less than 15 min to remove the old ice maker and replace it with the new one----and it works. You helped me save close to $200.00. Thank you!!!

Used the instructions on your site.

Required removal of the entire endcap piece. A total of 5 screws. Hardest part was realizing i didn't have the right size socket wrench to start. Got that and replaced all 5 screws in under 5 minutes. $18 for part, $10 for tool.

Disconnted current icemaker and removed from freezer. Took off front cover and long arm that control ice dispenser. Put cover and control arm on new icemaker, reconnected bundled wires into new icemaker and clipped along side of icemaker and remounted into freezer. Connnected into back panel for power and checked water supply line to make sure it was lined up properly and job was done. Made sure arm was in down position, had ice cubes in an approx 90 mins.

Replaced ice maker assembly, 5 screws out, unplug the wire, take some attachments off the old ice maker and put it on the new one, plug it in, 5 screws in...done. I did have to take a mirror to see how to unclip the wire, which turned out to be the hardest part of the whole job..

It was easy and my daughter did most of the work while I assisted.
Removed contents from freezer, unplugged refrigerator, shut off water to ice maker. Used hairdryer to thaw inside, placed ice catcher in sink to thaw. Removed defective ice maker and transferred trip lever and wire bundle to new unit. Installed new unit, bent mounting bracket located on bottom of new unit so that when installed the ice maker is horozontally level. Plugged refrig in and turned on water. Water does not come in right away as the temp probably has to be restored to freezing level before things start to work....so just let it run. In the morning lots of nice cubes and no leaks...hooray!

Had to remove the ice-maker (also easier than trying to work inside the freezer letting all the cold air out). A few mounting screws and an electrical connection in the back. After it was out you will need to remove the cover (not the superficial cover that just pries off) where the gear is behind it, just far enough so you can get the mounting tabs on the ice-stripper in. In order to to move this cover out, after removing the screws (the obvious), you'll need needle nose pliers to ever so slightly squeeze the plastic clips together that hold the plastic movable bracket and the metal ice level arm/switch, so it will pop out. Once you have room to put the ice stripper in, it should just all snap back together, then proceed in reverse to put it all back together.

I had several times tried to get the old switch out but with no success. Ordered the "repair kit" and followed directions for removing old switch (there is a plastic spring clip on one side). Easy to unplug the old switch, plug the leads into the new one, snap the new one into place. Took about 5 minutes total--piece of cake. I wish I'd thought to try this years ago when the old switch began to fail.

Removed mounting screws
Disconnected file hose
Flipped unit over to remove connecter
(This was the only difficult operation; unpluging & pluging it in)
New part fit was very good
Reversed the disassembly order to install
New assembly had to cycle a while to produce ice cubes. I'm very happy now, so bring on the hot weather.

removed the old filter. unwrapped the new one. peeled off the protective foil. inserted new filter as directed. placed old filter in sink to drain. ran "water" from dispenser to purge air from line. Shazam!

20 seconds. Easy Easy.

I'm uoset that I sat and looked at the broken piece for a month wondering"what the heck is this going to cost me" The more you spend on the appliance the more they break. The repair was too easy. Remove the 2 drawers, remove the bottom draw and there are 3 nuts you need to back off. The whole piece comes off really easy. I left the drawer glide on and took it off after the whole piece was out. Attach the glide to new piece put it in place and screw it back together. Now gow wash the drawers and glass that you have been putting off and reinstall them. Start to finish 10 minutes,.