Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JFC2087HRS > Instructions

JFC2087HRS Jenn-Air Refrigerator - Instructions

All installation instructions for JFC2087HRS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JFC2087HRS
706-720 of 757
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigerator and freezer stopped cooling. Compressor pump not coming on

  • Customer: Joseph from North Anddover, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed the cover panel. There is a clip that holds the relay and capacitor to the pump. Use a screwdriver to pry it off. Unplug the relay. The capacitor is plugged into the relay and they come together which was a surprise, I thought I only ordered the relay. Unplug a cable from the relay. Insert that cable into the new relay and plug it into the compressor. Reattach the clip. One be important instruction. Unplug the refrigerator for at least 8 hours before installation to allow the compressor to cool down. I tried first without allowing the compressor to cool and it did not work. After letting it cool I tried again and it worked like charm. Make sure the refrigerator is unplugged when doing the repair

Old ice maker worked irratically and finally quit for good.

  • Customer: Richard from Peoria, AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video and advice from the many others on this site and only have a few additional comments. First, the decorative cover on the front of the old unit is held on with two plastic teeth on the top and bottom of the cover. This was not at all apparent and it took me awhile to figure it out. I used a sharp knife to pry up the top edge until the teeth lost their grip on the metal notches in the old unit. Second, don't try to pull the cables out of the front of the old unit before removing that cover. It is held in with a plastic snap that must be depressed after the cover is removed. The video does a good job explaining how to remove the old metal arm and attach it to the new unit so that it will recognize the ice level in the bucket. Finally, don't bother looking around the web site for a button that enables you to add to these comments. You'll be contacted by email in a week or two for that.

Freezer freezing up in back and frig getting warm

  • Customer: Heidi from Etters, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
This is the 2nd Jazz board that we replaced in 2 years. We believe that a power surge caused the board to no longer work. We now have the fridge plugged into a surge protector. The instruction sheet to program the jazz board did NOT come with this part. I called Parts Select and they gave me a number for Whirlpool. I spent over 30 mins. talking to Whirlpool, 2 different departments, and they do not have instructions for this part. I was told that they only supply instructions for about 10% of the parts that they distribute. I was able to find the instruction sheet on my own but searching "whirlpool instruction 16022940." I hope this helps!

Switch didn't work

  • Customer: Don from Laramie, WY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

The refrigerator side is too cold, ice maker and water do not work.

  • Customer: Dierdre from Brentwood, NH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I'm a pretty handy person generally but I had to call on my engineer neighbor to help. I've never soldered before so I didn't feel comfortable installing the thermistor. I had everything ready for him so all he did was cut the existing thermistor out, strip the wires on the replacement , solder and tape and he was seriously done in 10 minutes! I replaced everything and plugged the fridge in to find that my fridge still freezes everything. I have now ordered the damper control and gasket to hopefully fix this problem.

Ice maker quit working and had water leak

  • Customer: mike from Sunset Hills, MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Your video was very helpful and accurate. However, my freezer is a bottom drawer type, so I needed to remove the freezer door first. There were 4 nutscrews which needed to be loosened, and door lifted off. Now with the door off, and both baskets removed, access to the ice maker was easy like your video. Also, the freezer compartment was much more accessible for cleaning as well. In 2 days after replacing the ice maker, we have had 2 full batches of ice, with full sized cubes! Your ecommerce shopping, delivery, and instructional videos made for a great on line buying and installation experience. Note: The Dacor ice maker was replaced with a Whirlpool ice maker part. Your replacement part was identical in all respects to the original equipment even though Dacor was not included in your list of compatible brands.

ice maker not working

  • Customer: Amy from Caledonia, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
watched the video you have on installation and followed it with ease. The only part you need a tool is to loosen the first nut and then everything else pretty much pops out and you reinstall with the new part. The icemaker worked within an hour and makes perfect cubes. The videos are super helpful.

Ice maker was leaking and needed to be replaced

  • Customer: Rochelle from New City, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed the instructions shown on the YouTube video on the Parts Select site. I had to make a few modifications. There were two nuts that had to be loosened to lift the ice maker off the freezer wall. The mounting bracket had to be transferred from the old icemaker to the new one to align with the hole in the freezer to reattach. The white wire went under the clip was a black wire but it was easily recognized. Other than that it was very straight forward and I had new ice in a few hours. I would definitely do it again.

The ice maker that came with the refig stopped working after 1 YR!

  • Customer: Darwin from Sioux Falls, SD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
If you watch the video on PartsSelect that will give you a general idea of how to do the repair except mine was in a bottom drawer freezer. You have streach a little to get to the screws holding the ice maker to un-screw them just enough to lift the ice maker out.

Ice maker was dripping and creating a giant ice block

  • Customer: Sharon from Saint Augustine, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I never would have imagined that my husband and I could replace our ice maker so easily. We simply fired up the step-by-step video on my tablet, paused it as we did each step and voila! Usually there is a lot of cussing with any repair we do and I don't think there was even one cuss word uttered. Thank you for the clear and concise instructions!

The ice maker stopped working and left "kling-ons" in the tray. At one time the trays kept trying to fill which only sent water pouring into the freezer compartment.

  • Customer: Patrick from Fairfax, VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Searching Google and Youtube produced trouble-shooting guidance to first check the water inlet valve which I did. I should have realized the valve was working since the ice-maker was trying to fill the trays. Additional advice recommended skipping all the other component troubleshooting and merely replace the old unit which I did. The big difference with the Amana appliance was the icemaker was installed laterally in the back of the freezer rather than longitudinally with the end of the control wheel positioned towards the front of the freezer. This created a tight fit in removing the old unit, especially since the wiring harness was extremely short. The latter made access to the plug release catch difficult. I used a small flat blade screwdriver and worked mainly by feel to release the plug catch. Persistent wrangling finally got the plug detached and the unit free. The water inlet hose also had a rear access orientation while the replacement unit had access was from the side. The hacksaw blade was used to cut a pre-outlined access to allow the hose to enter from the rear as with the old unit. Once the shut-off bail was transferred, wiring harness reconnected, and water inlet positioned and clipped into place, the mounting screws were secured. Within 24 hrs the first ice cubes popped and the unit has filled the ice reservoir. Keep in mind I just ordered the icemaker and did not need any other add-ons like a different wiring harness which seemed to work fine. Confirm when you order you don't need any additional parts. Good service for PartSelect. I will use them again.

Ice maker started spilling water and then stopped making ice

  • Customer: Daniel from Chicago, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
1. Watch the video. 2. Save your old ice maker's cover, metal lift bar, and power cord and clip. New one does not come with the cover, metal lift bar and power cord and power cord clip 3. My ice maker had three screw. two on top that only need to be loosened. on e on the bottom that has to be removed

ice maker quit making ice

  • Customer: denton from grinnell, IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unplugged the refrigerator.Removed the nut on the front bottom side from the support bracket with a nut driver.Pull down and out the old icemaker but not clear out to remove the electrical connector reaching to the back . Re-used the old front cover and the wire support clips and the wire connector assembly.Also put the shut off wire on the new icemaker.Re-installed in reverse sequence and waited for ice cubes to be made.Make sure the water line coming in the back goes to the ice tray.

Ice maker had been leaking for several months and needed replaced

  • Customer: Joe from Leonard, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I took the old part out and put the new one in and it works like it should. I loosened two screws and took one screw out with nutdriver. then I used the old wiring harness, bail and cover to finish.

The ice maker had been dripping and than stopped making ice. I worked with it and got it to work again for a few days and than the same problem occured.

  • Customer: Kathleen from Waller, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video on line first. I shut off the power to the refreigerator. I took the one screw out on the bottom of the ice-maker and pushed up on the ice maker. Than I disconnected the power harness inside the refrigerator. I took it out and changed out the harness from the old one to the new one and also the bar that dumps the ice. I reconnectected the harness to the back of the refrigerator, made sure that the water spout lined up correctly. Pushed the ice maker down on the screws and reconnected the screw that I had removed. Waited about 1 hour and had ice cubes. This was an easy process after watching the video.
All Instructions for the JFC2087HRS
706-720 of 757