JEW9630ACW Jenn-Air Wall Oven - Instructions

Turned the circuit breaker to "off"
Unbolted the unit from its cabinet (4 screws - visible when the oven doors are open - secured the unit in its cabinet)
Slid the unit out of the wall about 2 inches
Removed the control panel.
Unbolted the cooling fan assembly
Unplugged the assembly from the wiring harness
Removed the cooling fan from the oven

Plugged in the new cooling fan
Bolted the new fan in place
Replaced the control panel
Slid the unit back into position
Bolted the unit in place
Turned the circuit breaker back on
Tested

No problems - the hardest part was having to reach to the back of the oven from the front.

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

replaced broiler element - still would not heat.
Called repairman and the control panel is out and will cost around 200.00 to replace. To replace the element, my son helped as my arms weren't long enough. Removed two screws at back and two screws on front of broiler brace. Pulled out and removed wires and hooked them to the new element. Had to turn off circuit breaker. Pushed element back into the holes and replaced screws.
In this instance, it would have been cheaper had I just called the repairman first. However, I have an extra broiler element in case it goes out again.

SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

Diagnosis is the important aspect. Ovens have plunger-type switches to tell the "brain" door is closed, both for the light AND to allow initiation of self cleaning. Finally discovered one of those switches was "scratchy" in operation and unreliable in closing the circuit. (Push the plungers in and out several times and observe the light.) If not 100% reliable, replace that switch (cheap and easy with a Phillips screwdriver.) Initial guess was a $major "brain"-electronics problem but it was merely a sticky switch. Strange since the unit is about a year and a half old and rarely used. Found the part easily with PartSelect, and it came via UPS quickly.

Opened the box and removed the rack!! It's well-made, though not perfectly flat. But it works well in the convection cycle of the Jenn-Air which has a "drying" mode within the cycle. I've done basil and chives so far. The dealer from whom I bought the dual-fuel downdraft range did not mention the rack as an option. I found out about it through the range's manual. Great, quick service from PartSelect.

I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).

Removed 2 screws securing bake element, pulled element clear with wires still attached, then removed the wire push terminals. Attached terminals to new bake element and reinstalled. Extremely simple.

As the probe is a plug-in item that would normally be out of the oven, there was nothing more to the repair than checking that the new probe plug fitted the socket and that it was detected by the oven. Then the old probe was consigned to the trash.

Everything checked out, and the probe was used satisfactorily within a couple of days.

First, I searched ythe partselect.com web site for "Dim over display for Jenn-Air double over" and found an answer to some one with the exact same model as me. The answer said to order the "clock assembly" and all would be solved.

So, I ordered the assembly, it arrived. First thing I did was turn off the circut breaker for the over! I removed 4 screws holding the oven display in place. With those 4 screws removed, I was able to remove the clock assembly with 4 more screws and 3 cable connecters.

Put the new assembly in place, hooked up the connectors and turned the circut breaker back on. Everything was done and working within 15 minutes! Could not have been easier, it's great to have the display back again, we can now tell the oven temp, how much time is left on the timer, etc!

Removed old part with a pair of pliers and plugged the new part into place.

Very simple and the self cleaning feature works again.

Sunday, four days before Thanksgiving, our oven would not bake properly. A quick check indicated the top element was not working. What to do? Where to get a part in time to fix for Thanksgiving dinner? The answer was easy - PartSelect. I had the part in my hands on Tuesday AM. Oven was fixed in 15 minutes and my wife was baking pies within an hour. All worked well and yes, we had a wonderful trukey dinner. Great service !

Remove burner knobs, Removed 7 screws from bottom of face plate. Removed screws from 2 alluminum or steel spacers I guess you could call them. I let the Op Panel hang carefully not to stress wires. I marked all wires of the Latch asm. Removed the four screws holding it in and carefully removed the wires. Replaced in opposite manner and self cleaning works. The oven tried to start the cycle but I noticed the latch never triggered. When the function first stopped working I was able to apply slight force to the door and the latch fired. So after replacing the door switch it still failed to work. So latch asm was the official fix. So I have had to replace the latch asm and the Op Panel for being dim. I don't think this model is very good. But Partselect.com is great easy to find parts and good prices. Very pleased with my experience.

Turned off power to range - Removed the 4 screws holding the glass assembly in (front glass touch panel on range). and lifted up to expose wiring and electrical components. Pulled off all electrical plugs (4) and detached clock component from assembly by unscrewing 4 screws. Replaced new assembly, secured with 4 screws, plugged in all 4 plugs - turned circuit breaker on to restore power - WaLah!! That SIMPLE!

When I removed the bottom bake element and tested it with an ohm meter, it was an open circuit. Once the new one arrived, I simply had to hook up the two leads, screw the cover back on the back of the oven and the job was done.