Models > JES9800AAB > Instructions

JES9800AAB Jenn-Air Range - Instructions

All installation instructions for JES9800AAB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JES9800AAB
181-195 of 305
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Varying heat

  • Customer: Kimbel from Rhoadesville VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed two screws, unplugged the old unit, plugged in the new, screwed the new in. Job done. Would have been less than five minutes if I hadn't kept dropping the screws.

not heating/kicking oven off

  • Customer: Kevin from Virginia IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Husband got on partselect.com and read reviews, we ordered a long oven sensor kit. When it came in the mail, I took it out and look at it, decided I could probably switch the part.... and so I did. Easy Breezy ... and it worked well

bad surface burner switch

  • Customer: Lawrence from Birmingham AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
1. Turn off power at breaker. Take no chances. Turn on each working burner, fan, oven light to be sure there is no power to the appliance. Then, turn them off.
2. Pull knob on switch straight out to remove.
3. Remove 4 Phillips head screws under control panel. Pull panel gently down, then out toward you slightly to release top edge. Rest control panel on self-clean lock knob.
4. Confirm terminals on new switch match up with old switch.
5. Use needle-nose pliers to gently remove wires from old switch one at a time and place them on the
corresponding terminal on new the switch.
6. Reverse steps 3, 2 and 1. Test switch and burner.

Front right burner did not turn on

  • Customer: Vanna from St. Johnsbury VT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
We followed the instructions on the video after receiving our part - they were perfect instructions and led us right through the repair. I have to say it would have been harder to do with one person - but probably doable.

replaced the current warn-out grease filter

  • Customer: Joseph from East Greenwich RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
removed the old by pulling it out of track and replaced it with the new filter

Oven would not work

  • Customer: george from San Antonio TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 0 of 2 people found this instruction helpful
Installed new thermostat. Went well. Now the oven comes on and it takes 2.5 hours to come up to 250 degrees. Help!

The 6in burner would go to max heat regardless of the setting.

  • Customer: James from Dunnellon FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
Un screwed the two screws in the downdraft section enough to release the unit that holds the surface burner controls.Then removed the control nob, unscrewed the two screws that holds the switch in the unit, removed the wires, making sure the color of the wires were placed on the same contact point. Put it back together and it worked
fine.Of course I did shut off the power before starting any of the above

Burner only operated on high, no medium or low heat.

  • Customer: Paul from Collegeville PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 3 people found this instruction helpful
First I moved the left rear burner to the right front. No change. Then I moved the burner units from left to right, No change. I guessed it was the control switch and ordered from PartSelect. Turnaround time from PartSelect was excellent.
I turned off the powerr to the range. Removed the screws holding on the front panel and then pulled the panel out far enough to see behind it. I located the faulty control switch and then held the new switch, next to it, and turning to proper orientation. I then, one at a time moved the wires to the new switch. After that it was mount the new switch, put the panel back in place and turn on the power.

the original grease filter was worn and falling apart

  • Customer: Barbara from Medfield MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
Removed the old filter from the top of stove and put the new one in. Took about 10 seconds.

The filter in the grill section of my stove fell apart.

  • Customer: Beth from Dunkirk NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
I simply removed the old filter and replaced it w/the new filter. It came in record time and I'm very pleased w/the service I received.

Broken leveling leg.

  • Customer: Don from Crestwood MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

OVEN QUIT HEATING DID NOT NOTICE HOLE IN SIDE OF ELEMENT UNTIL I REMOVED IT

  • Customer: BRIAN from FOWLERVILLE MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
UNPLUGGED THE STOVE REMOVED BACK COVER PLATE UNPLUGGEG TWO WIRES REMOVED RACKS FROM OVEN REMOVED TWO SCREWS THAT HOLD BAKE ELEMENT IN PLACE AND REVERSED PROCESS

The burner didn't heat to full temperature.

  • Customer: Stephen from Grants Pass OR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First turn off the power to the stove/oven. Next I removed the 4 screws located on the bottom surface of the control panel. You need to open the oven door to see/access them. The control panel can then be removed by rotating the bottom outward which allows the flange on the top to disengage. Next remove the two screws that hold the switch to the control panel. Note which wire goes to which spade connector. A quick photo can help. Undo the wires. Remove the old switch. Reinstall the wires. Mount the new switch to the control panel. Mount the control panel back into the stove/oven. Turn on the power and test. The burner now works as new!

Oven door was locked, couldn't set oven temps

  • Customer: William from Nashville TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

The oven would not heat (bake element not turn red)

  • Customer: Robert from Mountain Grove MO
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Read the ID number from label and ordered part on line. Part was delivered next day. Shut off power to stove and Pulled stove out from cabinet setting. Took out about 12 screws from back pannel and removed it. Pulled out wires (easily seen) from each side of heating unit at back of stove. Went inside oven and took out 1 screw (easily seen) on each side of heating element at back of oven. Heating elemnet came right out. Reversed procedure for installing. Only tool used is a small Phillips screw driver.
All Instructions for the JES9800AAB
181-195 of 305