Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven erratic, not heating correctly, timer beeper sounding
The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.
Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.
Oven sensor caused cooling fan to run continuously. Had to flip breaker to get it to turn off..
Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.
Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.
Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.
I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane. It took less than an hour. Thanks for Your prompt service.
My husband replaced the convection fan with the one we ordered from your service. It was easy for him to repair and took approximately 1/2 hour. We were very happy with how quickly we received the part from your company. He had my oven fixed in time for me to do all of my holiday baking.
First I cut electric power off removed the two screws that hold glass top lifted up and removed two screws that hold element in place. I disonnected the wires and then pulled the element out
Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.
1) Remove 4 screws under front control panel. (Oven door needs to be open.) 2) Remove 2 flat head screws on sides of control panel. This will loosen control panel. Capture control panel to keep from hanging from wires/connectors. I used hooks made from a wire hanger. 3) Remove 2 screws to remove two steel panels on either side of stove. 4) Remove rear screw of the 2 front screws now exposed and 2 rear screws near top of stove. 5) Carefully flip over glass top being careful not to pull on the wires. 6) Identify burner to be replaced. Note 2 numbers where two clamps are attached to burner. 7) Using 3/8” nut driver, remove screws to allow removal of burner. Remove wires per included instructions. Remove burner. 8) Place new burner under clamps and align to the holes by the two numbers noted in step 6 above. 9) Connect wires to new burner as per included instructions. 10) Reverse removal steps.
While preheating the oven would often shut off. After manually restarting preheat again, the temperature would slowly rise until it shut off again. After several restarts the oven came to the desired temperature. It would hold that temperature. Other functions seemed to work fine. I could either fix
Shut off power to the range at the circuit breaker. Remove 2 Phillips screws at either end of the front panel on the L and R side. Open the oven door and remove 4 hex head screws under the panel. Lift up the panel and pull it forward gently. It slips out and hangs on all the wires connecting it to the stove. Unscrew the 4 Phillips screws holding the control panel frame in place. Take pictures of the back of the control board that show clearly the position of the 11 plugs inserted in the board. Gently remove each of the plugs either by pinching open the connector or simply wiggling it out. Insert each plug into the new control panel. This is relatively easy, since the plugs are color coded, differently shaped, and held in the correct position by their wires. Nevertheless after finishing check compliance with the pictures you took. Screw the new panel in place with the 4 Phillips screws. Reinstall the panel, turn on the power, and reset the clock.
