JER8855AAS Jenn-Air Range - Instructions

Removed the two screws that hold the back glass in place. Rotated old bulb out of it's lamp fixture and replaced it with the new bulb. Replaced glass and reinstalled the screws.
The hardest part was finding the bulb ... a very unique 18W flourescent. I wasted a couple of hours trying to locate it locally at my regular suppliers. The order at PatsSelect was easy and direct and the bulb was on my doorstep 3 days later .. an exact fit. Thanks guys.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires to remove the old sensor. Went on line to find out where to order it from. Ordered it, It was on back order but was only about 1 week to receive. Reversed the procedure. WA LA. It works great.

very very easy. but keep in mind that step one, killing the power at the power box. I jumped that one to a near disastours outcome, thankully all turned out well byt there was a hell of bang and VERY bright flash. Still was worth "doing it yourself" just keep in mine the cut power side...Safety first!!!

Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working correctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )

removed the screws,pulled the element out about 3 inches disconnected the 2 wires

As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

I removed the oven door, set up a work light, took digital pictures of cover plate (to confirm parts postions), marked the bottom of cover plate to remember cover plate position, removed 6 screws, unplugged convection fan unit, reposition replace fan unit in exact same position, attached fan unit cover plate, reinserted 6 screws. Receptacle bulb did not need replacement, just retighted existing light bulb after releaseing spring tension over glass dome of light bulb. Total time 22 minutes.

Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

First thing- I cut off power to the range. I then removed two screws to allow the cook top to be lifted. I marked the wiring and replaced the burner. Reapplied power and started cooking!

Turn off breaker.
Remove knob, pulls off. Pulled stove away from wall.
Removed front panel with switches attached.
There are screws in front and back.
Removed screws that hold switch in place.
Transferred wires one at at time to get proper location.
Reverse process for reassembly
Gary in Ohio

Piece of cake! Took more time to find the screwdriver than it did to replace the element!
Unplugged the stove. Removed 2 screws. Pulled the element out about 2" and disconnected the wires on each end (wires are attached to a metal clip that just pushes on to the end of the element. Threw the old element away. Unpacked the new elements. Connected the wires at each end. Pushed element into place and screwed in 2 screws. Plugged oven/stove back in and voila! That's it!

I had some confusion about the correct series number associated with my stove and called Partselect. They confirmed the part I was looking at was correct in less than 5 minutes. I then completed the order online. Even with standard shipping my order was processed immediately and I received the heating element the next day.

Turned off the breaker. Removed the two screws in the front holding the range top down. Loosened the screws holding the element in place while balancing the range top with my shoulder. Removed the wires from the older element one at a time and attached them to the new element. Put the new element in place and screwed back in place. If I had a little help with the range top I think I could have completed it in 5 minutes but I was at home alone and the other stories of doing this repair made it seem easy enough and it was.

I removed door by opening it to first stop and lifted it up off the hinge's. I removed all screws that held the inner panel to the outer panel and handle. Removed inner panel from outer panel, then glass and insulation, replaced glass and insulation and panel.

Replaced screws and handle,pulled hinge's out to first stop and slid door down on hinge's. This took about 20min. to do, most anybody handy with a screwdriver can do it.

PS: shipping was fast and price was great.
Thanks Bob G.

SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.