JE635WC03 General Electric Microwave - Instructions

Went on line and saw the Video - very simple to follow - very easy to remove and install the new switch -- went like a breeze!

Light bulb repair was super easy once I got the out shell of the microwave off. The unanticipated problem was that I didn't realize the outer shell was secured with unusual "Security Torx" screws I have a couple star screw drivers but these were very unusual and could not find a proper screwdriver to remove them. I was able to force them lose with a small philips screwdriver and a pair of channel lock pliers. It took me quite a while to get the screws off this way but once I got them out and the outer shell off the microwave the light bulb replacement took less than 10 minutes. You should market the appropriate screwdriver to remove the outer microwave shell with any interior replacement parts.

Was sent the wrong part but wanted a pizza so I installed it anyway and now the turntable turns a 6 rpm instead of 3 rpm. I figured that the part I ordered was no longer available and that was the best you could do for a replacement part. Replacement was easy- removed panel from bottom of microwave and filed the sharp edges from the side cutters, remove the one motor screw and motor. swapped the plug over and installed the new part. Replaced bottom panel, plugged in and cooked a pizza.

ordered the wrong part, (my mistake) new part took about 5 mins. no problem.

Ordering was simple, had pictures with descriptions so you have no problem finding the right part. Receive 3rd day after ordering. Motor Replacement was ever easy, remove screws holding bottom plate, unplug failed moter, remove mounting screws, remove failed motor - Install new motor and screws, plug in power cable - replace bottom pan, job done. As a side note, the original moter was 2-watts the replacement motor was 3-watts, more power means better motor, and this motor runs very quiet. Totally satisified.

Understand the type of fasteners GE used in the appliance require a BRISTOL type screwdrive.....unfortunatley this tool is not a part of my tool chest.....after running my four letter vocabulary and the use of thin blade screwdrive a a small vise grip plier was able to get the little bugers out.....thank goodness there was only four.

It took two people because we have built-in unit. The power plug was in cabinet above.First had to remove front frame in cabinet with Phillips screwdriver. Removed microwave from cabinet box (be sure to wear gloves, edges are very sharp). Then unscrew outer shell of microwave - easy process. Easy task to remove bulb/socket piece. We ordered part from Part Select - friendly service and the price is the best. Even with minimal shipping costs, the local prices were more than double. Important, it is a bulb and socket part.

My husband burned the microwave by using alumifoil. It was working for a little while after that but next day, the microwave was completely off. He thought the thermostat was broken, ordered the part and replace it. It's fixed and working fine now. Someone mentioned that if you put the broken thermostat in the freezer, it will be reset and fixed. I tried that also. I wrap the thermostat and put it in the freezer for one day. Now it's working!! I didn't know about that before I ordered the part but it wasn't expensive at all. So now, we have extra thermostat!!

First you have to get the "security screws" out with a pliers or vise grips then it was a snap, just replace the screws with 1/4 drive screws for the next time you have to get in there !

Simply remove the cover after unplugging the Microwave. The light is attached to a bracket and unplugs from the electrical system and then pops out. Replace with the new bulb and bracket, reattach the electrical connection and replace the cover. Less than 15 minutes. Just need a special star screwdriver bit with a hole in the middle to remove and replace the screws holding the cover to the frame.

After opening the case (the most difficult part of the job), tested the fuse (good) next in line on the power lead was the "flame sensor". With my ohmmeter it read open. The schematic noted that it opens at 212 degrees and closes at 32. Put it in the freezer for 15-20 minutes while I ordered a replacement. Upon rechecking, it had reset. Reinstalled it and everything works fine. I did receive the new one and it's on the shelf, just in case.

Remove bezel (4 Phillips sheet metal screws). Pull out unit and unplug from wall. Remove three sided steel cover (T15 or T20 safty bit required). Unclip double wire plug from base of lamp. Unclip and pull up on the lamp/bracket - discard. Push down new lamp/bracket, plug in wire socket to base of lamp/bracket. Replace steel cover and 4 'safety headed screws'. Lift unit, replug into wall socket. Insert into wall. Replace bezel and 4 Phillips sheet metal screws. Without the special "safety screw bit", this repair is impossible.

Replacing the light bulb is easy and takes no more than 15-30 minutes. The light bulb is located behind the grill on the right hand side of the microwave as you face the microwave. To get to the bulb you have to remove the outside cover. On mine there were three screws that had a special head and required a special tool. That was a surprise! To work around that, since I did not have the tool, I used a pair of needle nose pliers to grip and turn the screw head. They came out easily. I replaced them with the same size Phillips head sheet metal screw when I put the cover back on.
1. Remove the screws that secure outside cover and take the cover off.
2. Locate the light bulb and unplug the power wire. It is a two prong plug that pulls off with little effort.
3. Remove the old light bulb. It is held in place by a plastic tab. Push the tab toward the outside of the base plate with a small screw drive or your finger and lift the base plate. The bulb will come out with the base.
4. Install the new bulb. Align the holes in the base of the new bulb with the tabs on the socket and put the bulb in place, ensuring the tab secures the bulb base in place.
5. Reconnect the power wire to the bulb.
6. Reinstall the outside cover.
7. The light should come on when you open the microwave door.

Microwave outer case was held on by Torx screws, so needed to get a TT20. Removed case screws, removed case, unplugged thermostat cavity, removed small screw holding cavity in place. Plugged in new thermostat cavity, put small screw back, slid case back on. Plugged in microwave and still no power. Did everything again but also replaced the fuse. Plugged in microwave and it came right on. Has been working fine ever since.