Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
unplug oven from power remove glass turntable remove cabinet housing remove burnt out bulb order correct part reinstall new bulb reattach cabinet housing install glass turntable plug into power outlet confirm light bulb on
Remove upper grill, then control panel, then 2 screws hold door switch mounting bracket, that will let you roll the switches out to work on them. Remove each switch by carefully pushing back retainer clips. Diode a long pair of needlenose pliers is helpful. The control board in front of capacitor comes out with a flat screwdriver and pry up. Removing grnd wires helps
Remove the top of the microwave, regular phillips screws on sides, torque screws on back. Lift up back and slide off cover. Light bulb socket is easily detached and bulb unplugged and replaced. Slide cover from back lifted slightly so lip will slide into front of microwave, than replace screws. Be sure to unplug microwave before you start.
Turntable Stopped Working/Display Timer Would Countdown But Not Heat
With this model, you must remove the outer covering. Don't try to access the display unit from the front like I've seen in some other GE microwave videos. After removing the outer covering, the switches are easy to replace. They are very visible and easy to get to without taking any other parts off. You will see the door switches just behind the display board. Remove the switch and then remove the connecting wires to ensure you don't inadvertently brake a wire. You will need a tamper resistant star bit to remove 3 or 4 screws from the back panel. All other screws are philips head. I went ahead and replaced both switches (yes...there are two of them) and works like a charm. I saved an $800 microwave for less than $60 and know what to do if it happens again. Appears to be a common problem on this model. Thanks for others making a post...It saved me time and money reading others remarks. Good luck!
Microwave not turning on. All other functions operate
DISCONNECT THE POWER CORD and discharge the capacitor Leave unplugged overnight Remove vent grille by removing the 2 philips screws Remove the LED panel by removing 1 phillips screw Disconnect all connectors that plug into back of the LED board completely Remove the wires from the switches (3) at the inside edge of the microwave door Gently remove each switch housing and test all three switches for continuity Carefully replace non-functioning switches and reassemble the panel GOOD LUCK
I used a phillips screw driver and a special type bit to undo the screws from the cabinet and found the light bulb and took the old one out and put the new one in and put it back together.
Door Switch went bad, Internal Fan would run every time you open the door
Unscrewed the control panel (2 screws), lift up and let hang, with a plan screwdriver open bracket holding the switch, unplug 2 wires, replace with new switch, plug in the 2 wires, push switch back into bracket. Then slide on the control panel, put the 2 screws back. Easy fix.
First I had to accept the fact that the unit was designed to keep non-professional people from doing any repairs. The switch was installed in such a manner that I had to break the mounting to remove the switch, then drill a hole in the mounting to secure the new switch in place.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light didn't work
I assumed light was burned out and got a replacement bulb. Removed back and side screws with slight difficulity. Was not able to remove cover. The top front would not loosen. I tried every trick in my 80 year repertoire. I gave up and put it back together. I emailed PartSelect last week explaining the problem. So far no reply. I am sure I have the right model # and others seem to have little trouble removing the cover. I paid $85 + tax for the oven and it has worked well for about 8(?) years. From what I read here, I figured I could handle the bulb replacement. I'm just out the cost of the bulb and shipping and the oven still works. It would have been nice to have the light work again but we will just wait until it quits working and buy another inexpensive unit.
Removed cover, diagnosed problem, ordered part from Parts Select, received part in 2 days, replaced part, tested and replaced oven into built in space.
When trying to run, intermittently, the light would come on but the tray wouldn't rotate or cook. When the door was open, the tray would intermittently rotate.
I pulled out the unit and found 2 interlock switches that are depressed when the door closes. After cycling the door open/closed I found that one of the switches occasionally would stay depressed. The repair was easy (after I took off the panels so I could get to the switch) I simply removed 2 screws that attached the interlock switch assemblies to the main unit. Then I popped out the defective switch and popped in the new one. This did indeed fix my problem.