JDG3000W Jenn-Air Dryer - Instructions

Diagnosed the problem as a blown thermal fuse. Ordered High Limit Kit. Watched a YouTube video on how to replace the fuse. A little trouble with dropping a metal bracket -3- times to the bottom of the dryer. A little inginuity solved that problem. Replaced the high limit fuse, and thermal fuse. Cleaned duckwork thouroughly. Was very clogged with lint, which probably caused the overheat problem in the first place.Put everything back together, dryer fired right up!

Unplug appliance from power source. Started by simply using screwdriver or steel putty knife to snap up the top corners of the top section of the dryer. It swings open like the hood of a auto. Looked on the back side of the front panel and found small 5/16" bolts on either side. Removed these bolts and lifted up on the front panel to remove the panel. Slide panel out of the way far enough to access the coil kit on the lower front section of the dryer. (The wires going to the door control switch will allow this without unplugging.) May need a helper to hold the dryer drum up out of the way or prop it up as I did with a block of wood so you can easily unplug/re attach the coil wiring. There are two Phillips head screws that hold the coil keeper in place. Remove these two screws, unplug the two coils (front coil has a three connector plug and the one behind it has a two wore plug). the front coil has a small sleeve that I needed to transfer to the new coil in front. Inserted sleeve as it came out of the old coil, slid both coils back in place, replaced coil retainer being careful to line tabs on top of coils so that they lined up in the coil keeper. Replaced screws in coil keeper. Placed front panel back on being careful not to damage the felt liner that the drum spins on. Replaced the two bolts on the inner side of each corner of the front panel. Lowered the top panel and firmly pushed it back down so that the holders went in place. Plugged it up and it worked perfectly.

This repair is very simple. (1) remove the lint screen bracket on top - two phillips head screws. (2) Gently pry open the top of the dryer with a large flat head screwdriver. It hinges backward. (3) Remove the top two nuts on the front panel. Lift the panel upward off the lower brackets. The door wiring is still connected, so I just rotated the front panel to the side. The interior is now exposed. (4) Take the drum belt off the tensioner assembly and pull the drum out. (5) Remove the coil retention plate - two phillips screws. (6) Disconnect the old coils, install new coils. I started the dryer up while disassembled to ensure the new coils worked and the burner fired. But a word of caution ... don't run the burner long with the dryer apart, as it could overheat. After all of this, reverse the process. YouTube also has a couple good videos showing all of this visually. I have very average mechanical skills, and this was an easy job. Another word of caution: most of the metal surfaces inside the dryer have nice sharp edges. Invest in a good pair of gloves to avoid mincing your hands up.

First of all, Parts Select is a great service. By giving us an idea of what parts we needed we were able to buy them without a lot of expense. My son and I did this repair together, and it took us a long time. We found an excellent video for repair on the web, and then lost it and couldn't find it again. We had trouble even getting the dryer opened up. That is where a putty knife comes in handy. Be sure to find out how to open it; it will save you a lot of grief. It is supposed to be easy, but it wasn't. Still,it was great to get it fixed so inexpensively. I'll leave the "how I did it" part up to people who had an easier time, but no regrets that we did it. Parts select sent the parts right away.We ended up only using the coil kit.

flame sensor was a little tricky since a wrench was necessary since there was no clearance buy pretty simple put back plug in started still no heat after 6 min running time . now it coil kit so simple was surprised change out both and put cover back on plug in started and been drying ever since thanks for all your help

TURN OFF POWER TO DRYER............................. Pay attention to where everything is as you take it apart, so it can be put back the same way. Take out the two screws by the lint screen. Use flat tip screwdriver between space in front of top to help lift top. Use rag on tip of screwdriver so as not to scratch it. Take out two screws inside the front panel at the top. One on each side. Unhook the switch wiring. Lift up the front panel to take off. The tub will be loose, so it can be taken out to inspect other components. Some call the tub a drum. Be sure to see how the belt tensioner is attached, so it can be put back on the same way, if it comes loose. It is under the tub. Take out old belt. Put new belt around tub. Make sure the tub sets on the two rollers in the back of dryer. While holding tub, put the belt around the grooved pulley on the motor. Grooves are face down against the tub. Feed belt through the tensioner. Put the bottom of front in on the tabs. Be sure belt is still in place around pulley and tensioner etc. Hold tub through front door and close front. Put the two screws back in on each side. Close top and put the two screws in at the lint screen. Done. Turn power back on. Turn on dryer to see if it operates properly. If not, check out your repair to see if everything is connected properly.

Followed videos seen on the internet for my dryer's repair. Went exactly as shown.

Used PartSelect instructions for routing belt & a customer's valuable guidance.

I removed screws for the lint screen - TOP. Pry up top with screw driver. Disconnected inside top front 2 screws, removed door control wires, white and blue. Lift off front of dryer. Tip dryer back about 40 degrees against wall. Remove warn belt (not broken). Relocate idler bracket on the cabinet base, follow diagram which comes with the belt package. Be very careful that the belt is NOT on the side of the idler roller. I had to do this install a second time, because I had it wrong the first time. Even though I've done this repair 5 or 6 times, there's always a first time GOOF. Not really a hard job.

Threw away the printed instructions and followed the Part Select video ,featuring Steve...

Well my husband did the install and he said it was very easy??

Ordered thermal fuse and cycling thermostat

Opened the top, removed the front panel. Supported the drum with my foot while I replaced the coils. I used a very short screwdriver so I would not have to remove the drum.

Watched a you tube video on replacing a dryer belt for a whirlpool dryer. Perfect instructions. Dryer is working great.Thank you

I opened the 5x5" door in the front of the dryer. Unscrewed the clamp holding the two coils down replaced/reconnected the coils and screwed the clamp back down