JDE2000A Jenn-Air Dryer - Instructions

Absolute First thing to do - Unplug drier from power source.
1st I looked up the parts drawing on line. 2nd Took the front of the drier off . It was held on by two
hex head screws. iIused a four-in-one screwdriver as a nut driver. 3rd. Lifted the front off the two post that held the front on, being careful not to strecth the wiring. 4th Took old wheel off, by removing snap ring with a pair of pliers,it came right of, no puller was needed because the hub was out of round. 5th Pushed the new wheel on, being sure to line up the "D" shape to match the motor shaft.
I could not push the wheel all the way on so I took a short piece of 1/2 copper tubing and used that to drive the wheel into place. The tubing fit over the motor shaft and was smaller than the hub. Be careful to tap the plastic wheel on, you do not want to crack the wheel. 6th Put snap ring on -with pliers. Reassembled front. Finished.

I just removed 1 screw that held the safety thermostat in and replaced it. Then I removed the long screw that holds the heating element and the high limit fuse in place. Replaced the fuse, cleaned out the lint duct area. Closed the dryer lid and pluged it in, it worked fine.

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

I took apart the dryer by unscrewing the top and the front, front comes off by just undoing the two top screws on the inside. I figured it was something to do with the rollers since the noise was ciclycal. The hardest part was to put the drive belt back on. It helps to have a second person for about 5 minutes.

Watched the video on the site and it was spot-on! Super-easy, took like 10 minutes to replace the belt. Thanks!

My wife noticed a loud racket coming from the dryer. I took a look at it by opening the door and spinning the drum by hand and sure enough, the grinding, clunking noise continued. After a day of drying clothes, the noise got worse and then my wife said the clothes weren't getting dry at all. She could see the heating element glowing but the clothes would not dry. Sure enough, this was the case. While the dryer was turning, the outlet hose was still cold but the heater element was on. I went to the PartSelect site, entered the model number and looked at the common problems associated with noise. It said that the blower wheel was the second most likely issue. It also showed how to open the dryer and look for problem areas. First, unplug the dryer! Then, I took a putty knife (screwdriver would work - flathead) and pryed open the lid at each corner and opened the top. I then tilted the lid back against the wall to support the lid. There are two screws that hold the front panel of the dryer to the sides. They are on the inside of the cabinet up high near the top. I took these screws out and the front comes off by pulling the front panel away then up. There are three wires attached to a sensor on the front panel. I took a picture of these for reference and disconnected these wires to totally remove the panel. With the front panel off, I could see large clumps of lint trapped at the base of the filter screen. Now is a good time to vacuum this clean. Inside the cabinet at the bottom right, you can see the blower wheel. It was totally broken off the shaft that turned it. You can still spin the drum and see the shaft turn but the broken blower wheel would "clunk" around causing the noise. There are a small handfull of screws that hold the faceplate of the blower assembly on. Take these off and you will have full access to the blower wheel. DOn't worry about the wires on the sensor attached to the faceplate. If you want to take these off their clips, take a sharpie and write the color of wire each clip takes on the front of the faceplate for reference. The blower wheel is held on to the shaft by a circlip that is easily pushed off with a screwdriver or pliers and also a spring clip that is taken off with pliers by gripping the tabs with the pliers and squeezing the clip open. Save these two parts because the replacement wheel does not come with these pieces. I ordered the blower wheel, it was here in two days and replaced the wheel. Note: The wheel will take some effort to fully seat it on the shaft. You can take a hair dryer and warm the center of the wheel where the shaft will go thru to make the install easier. Do not use a hammer to beat the wheel onto the shaft or you will be ordering another wheel. I put my left hand behind the blower as support and pushed the wheel onto the shaft with my right hand and using a towel to cover the wheel center as padding. Reinstall the spring clip over the wheel shaft support and then pry the circlip back on the end of the shaft with pliers, reinstall the blower faceplate, reconnect any wires, reinstall the dryer front panel by first leaning the panel out and dropping the front panel onto the cabinet tabs at the bottom and then closing the front panel and screw it back down with the two screws. Reattach the three wires, close the lid, plug it in and your back in business. It took me longer to write this than it did to repair it. Good luck!

Popped top open, matched up parts, changed them. Dryer cranked up,got hug from wife. Done life is good.

Disconnect the power and gas supply so that you can slide dryer out and into an accessable area to work comfortablely. Removed top and front of dryer. When disconnecting numerous wires from the top controls, draw a simple color coded diagram for reconnection before you disconnect those wires. After removing the top and front, take out the drum and clean all the lint, money etc. out of the normally nonexcessable area of dryer. Place new belt on as you replace the drum. This takes two people; one to hold the drum in position and one to carefully work the new belt into place. Rotating the drum by hand will assist in the placement of the new belt on the drum. After reassembling the newly cleaned dryer it was a pleasure to try it and find a dryer that worked better than during its pre-repair use and it saved us the price of a repair call or a new dryer.

Un pluged and Moved it out from the Wall, Raised the top, found broken belt. ordered belt on line, 2 days belt came in. cleaned all dust and dirt out put greese on berrings for rollers bleu out vent hose with Leef Blower. put top down, pushed back. pluged in and turned on IT WORKS!!!

I googled 'replace dryer belt' and found instructions on the 'Virtual Repair Man' web site. After reading the instructions through twice I began.

First I removed lent filter and removed the two screws that hold the lent body in place. I rotated the top panel up and back and leaned it on the wall; proped up the dryer drum with some scrap wood pieces; rotated the front panel of the machine out enough to slip the new belt, groves down, around the drum; reinstalled the idler pulley under the drum; raised the drum slightly and reattached the front panel. Reattached the top panel and replaced the filter. Did a test run and worked good.

I got a price from Sears for the part and they were asking $45 just for the belt. I saved enough in parts and labor to take my wife out for a real nice dinner. thanks

After searching you site for other similar problems, we ordered the part that we thought we needed, it arrived within 3 days, my husband installed the part and the dryer started. The information you have on your site was great, it gives you an idea about what to test before having to call a repairman. There were several people that had the same problem and with their description it was easy to test the fuse. Thanks it saved us alot of money and time. I can't describe how the repair was done, my husband did it, but it was very easy

well, the hardest part is getting this thing apart - you have to take out the lint trap and remove the two screws from the top. Then I was trying to lift the top off - it's held in place by clips so you have to gently but firmly lift it off from the front end and let it open while still semi attached at the back (like a chest). Detach the electrical wires - they are just clipped in place. Then remove the screws (one on each side) that attach the front panel, and (and this is the hardest part if you don't know how it's attached). You have to SLIGHTLY LIFT the front straight up and then pull it away towards you. I just pulled it off, breaking the little attachers, which I subsequently had to weld back on with a welding compound and leave it overnight to set. the next day was pretty easy though...

The spinning drum is pretty easy to get out and you set it aside. Then I saw the belt pulley sitting there on the bottom of the dryer out of place -- fortunately with the belt there came instructions on how to instal it - READ THOSE INSTRUCTIONS - after that it's cake - put the belt around the center of the drum and feed it through the other parts underneath (this is easier if you tilt the dryer back a bit to get at it better. And you must pull back on that pulley after you have put it in place again - clips into the bottom of the dryer - it's supposed to have a lot of tension on it. Put it all back together and voila!

good luck!

Unplugged Power Cord, Removed Duct.
Pupped Top Lid Loose to Reveal Door Panel Screws. Removed Door Panel to Discover Blower Wheel had Disintergrated @ the Shaft..
Located Part from On-Line (as have in past) and
Placed Order, On-Line ( Of Course ).
Received Part, via: Fed-Ex in Two Days..
Whoo Hoo. Whole Family Welcomed the Repair.
ThanX . Satisfied Consumer :)

After removing the control panel face plate, the lid, the front panel, and the drum, I had to trouble shoot the wiring to determine the dead spot. I found it to be the thermal fuse for the heating element. I then unplugged the wires to the fuse, removed the fuse from the fuse bracket, and then replaced evrything in reverse order.

First unplugged dryer from outlet. Lightly pryed up on top of dryer to disengage retaining clips. Removed 2 screws holding sides and front panels together. Diconnected electrical connector from door switch. Remove clip retaining electrical harness of door switch from front panel. Removed front panel and placed to the side. Removed screws using a nut driver to retain the blower cover from blower wheel housing. Note there are 2 of the screws used to secure the blower cover to the base of the dryer, a phillip screw driver can be used for this. Also there is some sort of brace on the LH side of the blower cover that needs to be removed as well. Can be removed with either a phillips screw driver of nut driver. Remove retaining clip from motor shaft. Remove retainer clamp that had broke off from dryer duct work. Was able to us needle nose pliers for both. Removed old blower wheel and broken pieces. Vaccumed out lint build up with Shop Vac. Installed new blower wheel to shaft of motor. Had to lightly tap with rubber hammer to slide on to "D" shaped shaft of motor. Manually turned blower wheel to check out. Re-installed cover, front panel and lid in reverse order. Plugged in power cord. Told wife the dryer was fixed and became a hero, (might be because I started the next load of clothes).