Models > JDB7910AWB > Instructions

JDB7910AWB Jenn-Air Dishwasher - Instructions

All installation instructions for JDB7910AWB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDB7910AWB
466-480 of 551
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Clip broke holding adjustable rack for dishes

  • Customer: Jennifer from Plattsburgh NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Extremely easy to repair. I can't believe I didn't do this earlier.

a lower wheel assemby broke

  • Customer: Larry from Silver Spring MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I Googled parts for an Electrolux wheel and Parts Select came out with a picture that confirms the one that I need. The price of the item was very reasonable as compared to the official website of the manufacturer. I like what I saw and bougt 4pcs instead. I will recommend Part Select to my friends without hesitation.

upper dishrack had rusted and needed to be replaced

  • Customer: James from Calabash NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I found a short video on YouTube that showed me how easy it was to remove the old dishrack and install the new one. I would have never figured out how to get old diskrack out without watching short video clip. And, all I needed was my fingers to undo the end clips.

the right side folding shelf on the upper rack rusted through

  • Customer: Judith from Old Greenwich CT
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I took the suggestion of a previous reviewer to bend the new part in. But instead of using pliers to remove the old part, I tried bending it to get it out. This was so that I could see how much force would be necessary to bend it without breaking it to get the new part in. I bent it in the middle and was able to get it unhooked from one side without too much force. To get the new piece in, first I made sure I had it lined up correctly. Then I inserted the circle over one of the side prongs to hold it and gently but firmly bent the piece in the middle until the circle on the other side could slip over the other prong. It was not bent enough to stay bent, just to compress it into the space and have it spring back to full length.

Hanging upper dish rack and Lower dish rack sticking

  • Customer: Luis from Sewickley PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Once I identified the model number it was really easy to spot the right part numbers I needed for my repair, the ordering system was easy and in a few hours a I got my order shipment information, the service was absolutely superb, the parts snapped in without problem and in a few minutes I got my dishwasher back in good operating condition.

water leak - tub overflow

  • Customer: walter from salisbury NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
remove panel on front to acess float @ float switch.Remove phillips screw to float switch,remove palnut from float shaft with 5/16 nutdriver.Remove float from inside washer.Reinstall new parts reverse order.

No water from rotating lower spray arm or center spindle; soap dispenser lid would not open.

  • Customer: ROBERT from MORTON IL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Had service man: stated I would need new motor/pump at $400 complete. I didn't like the interior of new dishwashers. Nothing to lose, so I verified that the motor was working; reviewed short PartSelect video. Ref: very helpful PartSelect assembly diagrams with parts list. THANKS PS! Removed two dish racks (top rack: extend fully and flip the roller-keeper clips. Pull rollers and rack-pins apart) Then I started taking the pump apart all the way down to the pump base (fits into tub with seal - did not replace that seal). Very intuitive - some parts are tight and must be encouraged to come apart; take care of seals and o-rings; take notes of sequence if necessary. Look for parts requiring replacement. Unscrew Spray Tower Lower Extension Nozzle and lift off Spray Arm and two lower spray arm seals - check seals for wear. Unscrew pencil-like Spray Arm Support Nut. Cause: I found a totally-clogged Pump Housing Filter, a bit of steel wool about the size of my thumb (same size as water supply opening in bottom), and small piece of broken glass. Cleaned all parts coated with lime; new Pump Housing Filter (could not clean adequately). Cleaned the screens underside of filter support (difficult) with brush and wire. Replaced o-rings for Wash Impeller and Drain Impeller as a matter of principle. Only alignment requirement is with bottom water supplly hole. Everything works like new now! Recommendation: clean Pump Housing Filter annually.

Just as you said...would not start, but was trying.

  • Customer: Andre from Van Buren ME
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Changed the latch with switches....a breeze. Now working like a charm! Thanks!

door would fall down

  • Customer: Louis Jr. from Trinity FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Real easy. I checked out the instruction video. It was great no problem making the repair....Thanks

Nasty appearing pump seal

  • Customer: Jerry from Nevada City CA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Unscrew round keeper on top of spray arm -CCW. Lift off spray arm. Remove the six Torx head screws aroun pump housing. Lift off pump housing. Unplug unit and obtain a small piece of 2 x 4 wood to block up the motor underneath. Push the white plastic lever near the left side of motor towards the back to loosen the entire unit. Place the wood block uner the motor and you will see the seal is accessable inside the dishwasher. Remove the seal and very carefully clean the area that accepts the new seal. Remove the block and pull back on the white plastic lever. Done!

Water leak

  • Customer: Tom from Oshkosh WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
With dishwasher removed from cabinet, I next removed the dishwasher racks and with a large adjustable wrench turned the vent cover (located on side wall) inside the dishwasher counter-clockwise a quarter of a turn or so and removed the vent cover and then air/ water inlet unit from the outside of the machine. I cleaned the unit and washer wall area prior to replacing the gasket. Replaced the gasket in the air/water inlet vent and reassembled in reverse order. Entire gasket replacement repair took about 5 minutes or less. Most of the time in this project is spent removing and then replacing the dishwasher in the cabinet cavity. My total project time was about 30 minutes.

Not cleaning properly due to clogged parts.

  • Customer: Maurice from Wappingers Falls NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I disassembled parts from the lower Spray arm to the Rinse Arm. Everything was gunked up, nothing was broken. I replaced the Lower Spray Arm, Secondary Filter, Pump Housing Filter and the Rinse Arm. I re-used The Radiant Shields, Filter Plate, Lower Spray Arm Seals and the O-Ring. Much of my time was spent cleaning before re-assembly. Assembly was no problem. I ran the machine afterward with no problems and very good cleaning results. I ran the videos once before starting. They were very helpful, as were some other people's experiences.

Bottom of basket was cracking and silverware were falling thru.

  • Customer: Nathan from brooklyn OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Please be aware the basket shown on this site is the original basket that came with the dishwasher. The basket they sent is not original. It is the dark grey basket found on every other site when searching for this item. You can save yourself some cash buying this non original basket from at least a half dozen other sites.

Rusted rack

  • Customer: Hank from La Habra CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The Whirlpool page had a link to a YouTube step by step instruction with pictures. The dish rack stop was very non intuitive - without the YouYube, it would have been impossible

Drain pump wouldn’t stop running.

  • Customer: steve from ramsey MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Eventually the Pump started making a lot of noise.
Replaced float switch, (Tells the pump to shut off when empty) initial problem fixed.
Pump running dry caused upper pump housing failure, replaced pump housing, no more noise.
All Instructions for the JDB7910AWB
466-480 of 551