JDB2150AWP Jenn-Air Dishwasher - Instructions

I just opened the package, pulled out the baskets, separated them and put them directly in the dishwasher. The video showed the part and size of the baskets which was very helpful. The delivery was EXCELLENT!!! I would purchase from PartSelect again!

I took the old one out of the dishwasher and put the new one in. The new one is much nicer and heavier than the original one!

Followed video. Everything went together fine, but leaked water around motor shaft seal. Read comments section on video and someone had the same problem. I had pushed the seal into base too deep. I pulled it out and reseated it. It worked without leaking after that. Bob

took inside front off disconnect wires pull old unit out and put new unit in then put inside front back on tighten screws was done unit works like a new machine

First turn off power and water then Removed the two screws on the bottom plate, took the plate off. To remove the valve , I took one screw out of the bracket and just loosened the other,Pulled the valve out ,removed the water lines,then reused existing brass connection, put the hoses on the new valve then put it back together .Turned the water on checked for leaks, then closed it up..Turned the power on and it works great.....

my dishwasher is located in a island so i pulled the paneling off the back & the covers off the bottom of the dishwasher. my water shut off is under the dishwasher. i shut it off unhooked the water line at the union shut off the electric, unpluged the valve, pulled 4 screws out of the valve bracket , slide the clamp off the hose and removed the hose from the valve took the valve unit out removed the water line from the old valve put it on the new valve reassembled it turned water on checked for leaks turned the electric on and tried it out.

Just dropped it in and that was it.

Took old basket out, put new basket in

Took out old, put in new; threw away old. :-)

The rack threads through this part. I needed to remove the rack along with this part by carefully unlocking the rack through its rear latch. Then I removed the protector cap of the portion of rack sticking through tine latch. Then carefully withdrew the rack from the tine latch. Then threaded the rack in the same way through the replacement latch. Then attached this latch with the rack to the tray and re-hooked the rear part. ONLY tricky part is to realize that rack needs to be removed along with the tine latch to be able to replace it.

Snapped on 5 new wheels in under 5 minutes and this raised lower shelf to keep from hitting circulating water spigots beneath the shelf. Cleans like it was new again!

The actual repair was pretty easy except the cleaning of the old gasket. It was melted and smeared all over the place, had to use mineral spirts to clean everything once i removed all the parts. Star screw driver with the power off i removed all the screws down to the pump, unlocked 3 locking clips from below the unit and removed the gasket without having to remove the motor. Cleaned everything and reassembled works perfect. use the diagram of that model to how to reassemble or take pictures

I initially took everything out and cleaned everything with the shop vac, and outside with the garden hose. That did not work, so I looked on parts select for a new accumulator filter, as I was not able to clean that very well. To install the new filter, I removed the sliding racks, top and bottom, and the water manifold, then removed the lower wash arm, then the parts under that, the filter plate, the outlet, the impeller, all the way to the accumulator filter. After removing that, installation was the reverse. I also cleaned the middle washing arm, and the lower, as I noticed food particles blocking the outer holes. All is good now, and the dishwasher, which we use almost every day, is working fine.

I unplugged the dishwasher under the sink. I opened the dishwasher up and took out the 12 screws holding the inside door facing on. I gently moved the door facing down towards the dishwasher to reveal the door locking mechanism at the top of the door. I unplugged the mechanism and plugged in the new one. I put the door back together the same way I had taken it apart. In all it took about 12 minutes. Works like a charm.

Routine repair. There are videos on the net that show exactly how to replace the filter unit. However, when you order the filter, order a replacement pump impeller. The impeller must be removed to remove the filter on this model. The impeller was stuck on the shaft, and I had to destroy it with the side cutter pliers to get it off. Before putting the new one on, clean the pump shaft thoroughly and lube the shaft with silicon lube or vaseline jelly. Clean the bottom of the water pan thoroughly, then reassemble. Then pour one cup of vinegar in the bottom of the dishwasher and run it with no dishes. This will clean the inside of the dishwasher.