Models > JDB1270AWY > Instructions

JDB1270AWY Jenn-Air Dishwasher - Instructions

All installation instructions for JDB1270AWY parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDB1270AWY
31-45 of 324
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Low water pressure during wash

  • Customer: John from Thornton CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 6 of 8 people found this instruction helpful
Removed filter cover and filter and found the plastic chopper sleeve was stripped out. Followed instructions that came with the seal kit to replace it.

Motor would not turn the impeller, no wash pressure.

  • Customer: mark from blackwood NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 5 of 5 people found this instruction helpful
Not a bad repair once you diagnose the problem. Took me three tries to figure it out. Just make sure you follow the instructions. I used an allen wrench to hold the motor in place while tightening the part onto the motor shaft, this way I didn't have to remove and flip the dishwasher to do the repair. The good news is the replacement part I needed was metal instead of plastic, thus I should never have this problem again. I don't understand why it was plastic in the first place but all of my appliance problems seem to be made to fail after several years of service.
Repair was

Closer tab on the door broken.

  • Customer: Paul from Austin TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
All that was broken on the old detergent dispenser was the door but the door can not be ordered without buying the whole detergent/rinse aid assembly. When I got the new item I just removed the old door and replaced it with the new door that I had taken off the new one. I still have the new detergent/rinse aid assembly that I can keep if I need to change it in the future.

Dishwasher would not spray water. Water would drain but not spray

  • Customer: Linda from Washington WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
Removed the basketsThen removed the bottom spray arm with nut driver. Removed the cover and spray tower assembly. removed screw holding broken impeller. Replaced and reversed process. Really easy. As an aside. This dishwasher has been a major disappointment. lots of things not holding up. Didn't go cheap when buying it. Nice to find a site with good prices for parts

drain line had split

  • Customer: William from Interlochen MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 7 of 12 people found this instruction helpful
disconnected unit (electrical, water, and waste) un mounted from countertop, removed from under countertop, unscrewed hose clamb, cut off wire tie. Attached new hose and wire tie (not included) reversed above steps. Done in about 15 minutes

Upper Rack not Cleaning

  • Customer: Stephen J from Sammamish WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
First I read all the reports for not cleaning properly already listed on this site. I had to replace the docking station with flappers. When I removed the station I lost the flappers down the water delivery tube just like Jon said I would in his repair post so I removed the water distribution assembly fished out the old flappers and snapped in the new.
But then I figured I might as well check out the accumulator while I was in the tub anyway - I had read that you need Torx screwdriver bit, which I had, undid the screws, pulled out the accumulator screen which was about 80% clogged, discovered I need a new chopper blade and my impeller is disintegrating, put it back together and lost ten minutes looking for the three screws I had incorrectly put in too soon, and now it is cleaning a packed full load like it was supposed to do.
**I love this site - I went to the virtual repairman and it listed every problem I had with this appliance in the order they happened (door latch broke years ago). - I think I am going to look up stuff that I own so I will know ahead what could go wrong with them.

And absolutely NO DUCT TAPE was used in this repair.

One of the wheels broke that holds the rack up.

  • Customer: Mark from Aloha OR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 5 of 7 people found this instruction helpful
I unscrewed the old rack adjuster assembly and screwed the new one on (this was after I took the rack out of the diswasher) -- I actually saved one of the old intact plastic wheels for future repairs.

Broken wheel in upper rack

  • Customer: Camille from Mill Creek WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 4 of 4 people found this instruction helpful
I removed the old rack adjuster by unscrewing four screws. I put the new rack adjuster in place, carefully fitted the adjustment parts together, then replaced the four screws. The best part of the repair was that Parts Select had originally indicated that my part would be on back order for a few weeks, but I actually received the part within just a few days. What a nice surprise - thanks!

If you don't hold door when opening, it will drop down hard

  • Customer: Peter from Westbury NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
First I removed two bottom plates (two screws on each) Then I pulled dishwasher out about six inches. That's as far as it would go because I did not disconnect the water and drain hoses. That was enough to remove the broken cable and collect the disabled spring. I then reattached the new cable to the spring and reworked them into position. NOTE: There is a right and left cable and spring set-up. I used the "good" side as a guide. I then pushed the dishwasher back into place and replaced the two bottom plates.

Our dishwasher would not take in water. It would partially fill but not to the level required to run properly.

  • Customer: Laurie from Cashton WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
I pulled the dishwasher out from under the countertop. It was quit easy to get to in the lower left front corner of the appliance. I loosened up the bracket that was holding the valve in place. Removed the wires, and taped and ID them so that I would know which one went where. Removed the hose clamp, pulled the hose off and removed the old valve. Put the new one back in just as I removed the old one in the same order. It was a snap! This is not the first time I have used PartSelect! Our evaporate fan went out on our refrigerator a couple years ago, replaced that. A shelf broke in our refrigerator twice, each one different at different times bought both from Part Select. This is the first place I look for help with repairs! I at least attempt to save money, then if it's too difficult I will hire a repairman. So Far, PartSelect has saved me a lot of money on doing it myself! Thanks PartSelect for making small repairs easy to tackle yourself, along with reasonable prices for parts!

Machine would not fill with water

  • Customer: David from Farmingdale NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 5 of 8 people found this instruction helpful
Remove the 4 screws at the lower panel, turn power off to dishwasher, remove single 1/4 attaching screw from float switch, open the door remove the old float assembly. Make sure you install the float in the machine first than side the switch over the end of the float before screwing it back in.

upper shelf dragging on slides ball bearing cage broke

  • Customer: paul from worcester MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 11 people found this instruction helpful
remove shelf install ball bearings in new ball cage click ball cage into slides re-install shelf piece of cake make sure you have all the ball bearings when ordering the cage they dont come with it 4/cage

original basket fell apart

  • Customer: D from Villas NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

Door handle stopped engaging

  • Customer: Harold L. from winamac IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
First I watched the repair video provided at your site. Once I got the right part, it went like a breeze. Just a phillips head screw driver and 5 minutes of my time. Speaking if the right part.... I would suggest that you remove the 'LATCH-DOOR-NO Handle' from your parts list.It only cause confusion in ordering the part I needed, and a loss of several days time in the repair cycle.
All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends.
Thanks,
Harold L.

The door would just flop down when you opened it

  • Customer: David from Plano TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
The spring mechanism is on the side, so you have to pull the dishwasher out onto the floor. To do that, you have to remove the floor molding (preferably without breaking it) and remove the base coverings (painted metal plates on the bottom of the washer. Unscrew the side gasket plates on the side of the dishwasher (just inside of the door) where it attaches to the cabinet and the screws in the braces at the top (inside the door) where it attaches to the counter top. Now you will be able to slide the washer forward to look at the sides where the door springs are. Depending on the floor, you may have to raise the washer's front feet. They screw up. As you pull the washer forward be careful to not mess up the insulation which drapes over the top and sides. You only need to come out 1/3 of the way to see the sides where there is a plastic wheel at the forward bottom corner. As you move the door up and down you can see the hook where the cable goes and further up the side you can see several notches where the spring goes. Hook the cable and bring it around the wheel and attach it to the spring. To reinstall, just follow these directions backwards. Good luck.
All Instructions for the JDB1270AWY
31-45 of 324