Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
old one cracked.
Pulled off old part, put on new. I bought 2 wheels because if one breaks, the rest are about to. May as well be ready. I spent appx $15.00. Repair by service person would have been well over $150.00
Silverware basket had broken through on the bottom and silverware would not stay in. Handle was tricky to put on. Bottom rack one of the adjustable racks had broken.
Removed the bottom tray. Removed the two clips in the top tray guides and removed the top tray. Removed the top spray arm and transfer tube by unclipping it from the top and at the back and then rotated it down and out. Removed the six screws around the upper pump housing and removed it along with the bottom spray arm. Removed the three screws holding the filter protector plate and removed it. Removed the two screws holding the accumulator / flow plate and removed it. Put it back together in reverse order careful to not over tighten the screws.
After noticing that the nozzles in the washer arms seemed clogged, I ordered replacements from PartSelect.com. Installing them was a breeze. The upper arm had a torx screw in it and the bottom just required a nut driver to get off. I replaced the arms and ran some DishWasher Magic through it and now my dishes are clean again!
Removed the bottom cover.with a flashlight and a mirror found the problem. Went to Maytag they told me that in 8 warehouses there were no parts. They did give me a enlarged view of the part that I needed. went on the computer to PartSelect called PartSelect talked to a very helpfull Lady ordered my parts. Job is done Mama's happy Lifeis good. Thank You
spring on one side of door broke, door became heavy and wouldn't stay up
Unscrewed dishwasher from counter and pulled it out from under the counter a few inches. Looked at the side of the dishwasher with the remaining good spring and saw how it was attached: One end was hooked to a little tether strung around a pulley, the other to one of a few steel slots. Copied that side for the new spring and works fine now.
Dishwasher was leaking do to heating element decay.
1.Disconnected the electricty 2. pulled the dishwasher from under the cabinet 3. tilted the washer on it's face (water supply was long enough and did not need to disconnected.)4. unscrerwed the 2 plastic nuts that hold the heating eliment in place. 5. tilted the dishwasher back upright and removed the old heating element. 6.put the new part in place had a helper tilt the washer forward while i tightened up the two plastic nuts to hold the part in place.7 reattached the elecrtic conectors to the heating element. 8. pushed the dishwasher back in place. 9 hook the electricity back up. During step 4 i had to remove the electric connectors from the old heating element.
from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.
First I watched the repair video provided at your site. Once I got the right part, it went like a breeze. Just a phillips head screw driver and 5 minutes of my time. Speaking if the right part.... I would suggest that you remove the 'LATCH-DOOR-NO Handle' from your parts list.It only cause confusion in ordering the part I needed, and a loss of several days time in the repair cycle. All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends. Thanks, Harold L.
The repair was much simpler than I had anticipated. I just started removing screws, remembering what screws went where, and carefully removed the parts I needed to until I could get to and remove the filter unit. Installing the new unit was a snap, then it was just a matter of putting everything back together.
Easy to repair and saved us replacing a dishwasher that was pretty new as it was. The dishes weren't getting clean, checked it out and found out the chopper was broken. Works great now with clean dishes.
I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.