All Installation Instructions for General Electric Range JCSP47BF6BB

Replaced damaged oven rack

I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.

Parts Used:

Vicki from Irvine, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

one leg of the terminal block was loose and overheated under load.the terminal block melted and could have caused a fire.

I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .

Parts Used:

Terminal Block Kit

brendan from lebanon, NH
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench set

Was this instruction helpful to you?

Thank you for voting!

Broiler heating element was not working

Turned off the circuit breaker. Removed 5 screws. Unplugged the heating element and then plugged in the new one and replaced the 5 screws. Very simple.

Parts Used:

Broil Element

Jim from Hyrum, UT
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

Was this instruction helpful to you?

Thank you for voting!

Bad Burner

I simply removed the 2 anchor screws in front of the stove and wrote down the wiring order on the instillation diagram, removed the old burner, removed the two studs, made sure they were installed on the right numbers place them in the new burner, wired the new burner, placed the springs respectively. Placed them in the correct holes in the frame to be sure that the burner was aligned properly. Put the washers on the studs and replaced the frame screws, lowered the cook top and returned the screws to lock the cook top in place.

Parts Used:

Large Haliant Burner with Limiter - 8"

Roosevelt from Waggaman, LA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

Was this instruction helpful to you?

Thank you for voting!

Broken drawer support

Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.

Parts Used:

REAR SUPPORT

Mario from Deer Park, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Thank you for voting!

Missing oven rack

I opened oven and pushed oven rack inside.

Parts Used:

Oven Rack

Damaris from Easton, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Broiler Element burnt out

The actual repair was relatively easy but access to the area in the oven made it a little difficult. Just unscrew 5 screws with a nut driver, unplug the old element, plug in the new element and reinstall the 5 screws. The only thing that made this repair difficult was being able to reach the connectors where you plug in the new element. They are loose wire connectors that don't reach very far out of the element receptacle. It was difficult to hold the end of the connector and plug in the new element because the oven door is in your way. Maybe it is easier if you take the oven door off first?

Parts Used:

Broil Element

Cherri from Katy, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Thank you for voting!

rear drawer supports broke

Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.

Parts Used:

REAR SUPPORT

TERRY from RICHMOND, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

Was this instruction helpful to you?

Thank you for voting!

Broil element on top oven was not working

Shut the power off at the electric box.Disconnected coil from roof clips.Pulled wire connection from back wall. Disconnected wire clips, connected new unit.Clipped to roof and turned on" Working fine".

Parts Used:

Broil Element

andrew from pittstown, NJ
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set

Was this instruction helpful to you?

Thank you for voting!

no racks to oven

Easily glide in.

Parts Used:

Oven Rack

Johnette from Baltimore, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Old dishwasher rack and silverware rack

The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!

Parts Used:

Oven Rack

Anne Marie from Andover, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

large burner on the dual element not working

The part arrived much sooner than I anticipated. The job was a little harder and took a little longer for me because I'm not good at repairing things. I usually have to call someone. However, I followed the step by step instructions that were provided both on the website and with the mailed item and had no problems. The instructions were clear and easy to follow. The tools needed were very basic - all of which I had on hand. If I could do it - anyone can.

Parts Used: