JCSP47BF6BB General Electric Range - Instructions

This was really easy, and pretty with no problems or issues It took me longer to write this than to do the actual installation. I used a digital camera to help me remember where things were, but a pen/paper works fine. Here's what I did:

1. Turn off the breaker for the cooktop.

2. Remove (2) 1/4" hex screws directly under cooktop. You may need to open oven door to reveal them.

2. Prop up cooktop. I used the box the replacement element came in.

3. The element is held in place with (3) brackets held in by a #2 philips screw each. Mark the location of each of the brackets. There are numbers on the element to help you do this.

4. Write down where each of the wires connects to the element. There's only a few of them, but I tend to forget that stuff. The wires have female spade-type connectors that connect to the male ends on the element.

5. Using a needle-nose or small pliers wiggle each wire off the element. Grab the wires by the end of the female connector when you do this. I found it helpful to use a small flat screwdriver to help pry them off. Mine were on pretty tight, so expect this to take a few mins. If you have problems getting to the wires, remove the brackets (next step) first and come back to this one. I let the element hang from the wires without any problems, but I still wouldn't recommend it.

6. Remove each of the screws with a #2 philips screwdriver. Support the element with your hand and gently pull each bracket away from the element. Once they're all gone, the element should just come out. I took a look at my old element and saw that the large burner wires were melted in a couple places, so it was definitely broken.

7. If necessary, clean the underside of the cooktop surface with a clean papertowel. There was a little dust from the old element on mine.

8. Connect the new element and test to make sure it works by turning on the breaker and turning on the burner for a second or two. Note: This will make the top of the element hot for some time, so test it and go away for a few mins. If it works OK, proceed. If not, disconnect and figure out what else may be wrong.

9. Using the old element, make copies of the marks you made for the bracket locations onto the new element. You'll have to punch through the insulation when re-attaching the screws.

10. Re-wire the new element, if necessary and re-attach the brackets over the marks you made. This may be a pretty tight fit because the new element was thicker than the old on mine. I opened up the brackets a bit to make it not so hard to re-attach. Hook the brackets on and squeeze them over the element. The holes in the brackets need to line up with the holes drilled into the bottom of the element. If they don't, spin the element around (or detach and re-attach the brackets) till they do.

11. Screw in the (3) screws over the brackets pushing them through the insulation on the element.

12. Close the cooktop and reattach the hex screws under it (1/4" hex).

13. Turn on the breaker and test again.

Thats it, works great now. Good Luck

Repair was very simple. Removed 2 screws under the cooktop, tilt the cooktop back, unplug 4 wires from 8" burner, remove two screws holding retaining clips, install new burner in reverse order. Very simple!

I had to remove the oven from the wall because the sensor plug connction is behind the unit. Two screws hold the sensor inside the oven and then I disconnected the lead and pulled the sensor out from the front. I installed the new sensor, tightened the two screws holding it in and connected the lead. Then reinstalled the oven into the wall. Overall, a very easy repair once you get the oven out.

The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. Unscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient

Open lid,un screw coil,pop in new coil snap holders in place,then cook a steak

Everybody said the Electronic clock oven control needed to be replaced, not the keypad. It was the keypad. Unpluged the range. Pulled the 4 burner control knobs off, Unscrewed the 4 burner contol knob bottoms to remove the panel cover, removed 2 of the keypad screws an loosened the other 2. Removed 4 screws holding the oven control panel. Turned the panel over to access the keypad wiring ribbon. Released the ribbon, turned the panel over to remove the old keypad. Put the new keypad ribbon through the panel and pushed the ribbon into the ribbon slot, put the anel beck in place with 4 screws, slipped the keypad in place on 2 loosened screws. put the remaining 2 screws back in. tightened all four screws. replace the control panel cover and knobs. Plug back in and viola.

The outer ring on the adjustable large haliant surface burner of our smooth top stove would not work. It would only work on the small (inner) size.

Found the part on this site, ordered, 3 days later, and it was fixing time.

2 screws removed to lift cooktop, 2 screws to remove old burner and disconnected 4 electric clips one at a time and placed them in same position on new burner. Replace the 4 screws and done.

VERY SIMPLE.

Unplugged range. Opened oven door and removed two screws from top of oven opening. Lifted oven top and propped up
with a 2 x 3.Unscrewed the two screws that were holding

The repair went very easy. The replacement part was designed differently than the original part. It installed on the rear of the drawer with a screw as the original snapped into the side. This was a bit confusing when researching and looking up the part online.

removed two phillips screws. Unplugged electrical connections replaced unit from PartSelect. They sent holder cover and new bulb (surprise). Great store with great directions.

Removed the oven door for easy acces to oven. Unscrewed (philips screwdriver) the screw holding temp sensor in place. Gently pulled the wiring until quick connector was located. Pushed down on locking level on quick connect while holding other end of wiring (so wiring would not fall back behind oven). Connected the new sensor and screwed back in place. Reinstalled oven door. Tested temperature settings by turning on oven and comparing with a separate oven thermometer.

Spring clips installed on seal just pull off door. New clips get inserted in mounting holes and are pushed in to seat in door. Seal ends slide into door holes.

Replaced old sensor with new one by removing nut screw and carefully pulling sensor cable out of oven back until plastic terminal connection is exposed. Sensor connection has a locking tab that must be pushed in to release sensor connector. Do not allow oven wire to pull back into back of oven until new sensor is connected. Reinstall nut screw and tight to hold new sensor in place. Verify proper oven operation.

Followed instructions and removed door. Loosened screws/bolts. Pulled the door apart. Removed the bracket that would hold the glass. Removed the broken glass and inserted the replacement glass. Re-assembled the door and reinstalled the door. Took all of 20 mins.

After turning the breaker off, using a 1/4 inch nut driver I removed all the clamp screws (5) holding the heating element in place. I then unplugged the element wire spades from the rear of oven and removed the old element. Installing the new one was simply going in reverse order. After plugging the new one in, I did however, use plyers to squeeze the connectors and make the connections tighter. It took a little more back work than I thought because I was leaning over most the time. All in all, I saved a hundred dollar bill in doing this 30 min job myself.

-Turn off breaker
-Undo the two screws that hold the top surface down
-Prop up top surface with a board
-Remove two screws/spring clips holding burner
-Transfer electrical plugs to new burner (this was the most challenging part)
-Screw new burner in place
-Lower surface
-Secure surface