JCB2059GES (PJCB2059GS0) Jenn-Air Refrigerator - Instructions

Removed Ice bin, remove rails on left side that hold ice bin. Remove one screw holding ice maker to refrigerator wall,then lift ice maker off holding screws. Unplug wire harness from back of refrigerator. Remove wire harness and loading wire from old ice maker and install on new unit. Re-install new ice maker by reversing steps. Videos where very helpful.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

After receiving the new ice maker assembly I placed the new part next to the old one to see what I needed to transfer from the old to the new. After removing the wiring harness and a few small parts, I placed them on the new assembly. After that it was a snap which timewise took about 15 minutes. I am pleased to say the ice hopper is full and being replenished very efficiently.

1. Prepare the new ice maker by installing the bail cut off from old unit and installing the wiring harness from old ice maker. 2. Turn off the freezer unit only and turn off water supply. 3. Unplugged the electrical connector from the ice maker to the plug in back of freezer compartment. Remove the three (3) screws holding ice maker in place. Placed the cap from old unit to new ice maker. 4. Plug the electrical connector to the plug in back of freezer. Attached new unit with the three screws. Place bail in on position and turn the freezer and water on, ice made in circa 3 hours (without leaking I might add :)

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

Easy

Just replaced a water/ice filter..

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

piece of cake to repair - great instructions!!

We had an Appliance Repair service come to fix, and they replaced the ice maker and the water valve, but ice maker was still not performing properly. We use RO water to fill the ice maker and because the water was also going through the charcoal cartridge, there wasn't enough water pressure to completely fill the tray. Plus charcoal filter was probably clogged. The original Blue Bypass Cap was nowhere to be found and I even called Kitchenaid to get one. They were of no help. But found your site, and found the part I needed. And best of all, ice maker is not jamming and is now making real ice cubes, not hollow, thin ones. And the water dispenser is now working too, so am very happy that such a small thing, fixed the big problem. Who knows, a clogged charcoal filter may have been the whole problem from the start.

I removed the end cap from the refrigerator by taking out three phillips head screws. Two additional screws were removed to demount the drawer track and remount it on the new molding. The new molding was re-attached to the refrigerator wall and now the cheese drawer has a functional cover. Very easy.

Mine was alittle different than the online instructions. 1. I removed the motor. 2. I took the fan off the old motor and cut the wires about 3" back from old motor. 3. Mounted the new fan on bracket and put the fan on the new motor. 4.connected wires that were cut and used wire nuts to connect. 5. Mounted bracket and motor/fan to unit and it works like its brand new. Thank you PartSelect!

The unit has two fans on it. One is located in the back and the other is locate inside the freezer section behind the panel. Remove the four bolts holding the door to the sliding rack. Remove the ice machine. Remove the back panel. Noticed that the fan was covered in ice thus shorting the fan motor. Tested for voltage to the fan was good. Replaced evaporator fan motor and unit works perfectly

I unscrewed the old filter and screwed the new filter in the way the instructions said. I have done this before with no problems. Easy fix.

I removed the cover on the water dispenser and replaced the parts with new parts ordered. The switch corrected the problem.