Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
broiler element circuit broke
First removed oven door, according to Reader's Digest repair manual, then removed two screws holding element. Pulled element out several inches, then removed one side of bracket holding up front of element so that bad element could be pulled further out. Then disconnected two red wires from one side and two light blue wires from other side. Removed old Element. Attached two light blue wires to one side and two red wires to other pole, inserted element back into rear wall and attached with two screws, Re-attached bracket holding up front of element. Re-installed door. Tested and it worked fine.
burner would not lay flat against surface of range.
Removed two clips that held the ceramic insulators in place. Removed two screws that held conductors to the burner. Replaced screws onto new burner unit, replaced ceramic insulators. Fastened clip to burner onto the range. Turned burner on and it worked great. Thank you for your quick responce to my order.
Lifted burner element to remove pressure on ring and drip bowl. Removed old parts and replaced in reverse order. This not intended to sound sexist, but my wife who is not particularily mechanically inclined performed the task on her own.
Removed 2 nuts holding the baking unit to the oven back, removed 2 nuts holding wires in place, installed new unit following procedure backwards. It takes longer to get the tools,take the oven door off, and take racks out than it does to remove and replace the baking unit.
Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory. Knott County Housing Authority Maintenance Personnel
Broiler element arrived at my door 3 days after ordering which was nice. Apparently the billing dept. is out of the USA so don't be surprised, like I was, to find a suspicious looking charge for a currency exchange fee (mine was 42 cents). I had to drill two new screw holes in the base of the new element in order for it to fit my oven. I also had to use heavy wire snips to cut off about an inch of the top of the new element base. The female electrical connections also had to be spread out with needle nose pliers since the new element connections were slightly thicker. With all of the issues I had I was frustrated and it took about two hours. On the other hand, the part works perfectly and was priced right. Hopefully it will fit perfectly out of the box for your oven.
I removed the unit easily with anut driver, however the unit also supported the thermo-link. I had to use the hack saw to relieve a small opening for the thermo-link to pass through. No real problem. Then a few holes to be drilled to attach the 'link' to the base of the broiler unit.
BUT-I went into the website listed on the box. GEAppliances.com Guess what? Their price was twice yours!!
Replaced the burner. Still no heat. Decided to take the front off and test the connections (Power Off!). Found no output from switch to burner. Ordered new switch from PartSelect. Switch arrived in 24 hours, just like the burner (I'm in FL, but still fast!) My only problem was that the know didn't quite fit -- too long. Cut the metal correctly, but still too long. Had to cut the plastic adapter slightly. Now it fits like the others, but it's not quite as secure due to shortening the piece that slides on the metal shaft.
turn off electricity to stove and simply remove the screws from the heating element and put new element back in place .put screws in and turn power back on and test.
replacing rusted drip pans on a 30 year old stove.
Just lifted the electric components Remove drip plans and trim rings and replaced with new drip pans and trim. Your company was incredible in there delivery of the parts..One day. You made my husbands very happy.
I looked on Youtube for a how to video. It was accurate but the screws in my oven were NOT phillips head screws, they turned out to be sheet metal screws. I used pliers at first which was a PAIN but then I borrowed a socket wrench from the neighbor that was MUCH better!! I had wanted to do it myself to prove to my husband and son that I could but I ended up needing their help because the screws were so tight.... But we did the repair ourselves!!!
Gasket sent did not match the profile of the original. Only after trimming off two long edges of the gasket did it come close to matching the original. I would not recommend using this replacement gasket for this oven model. 1-Remove door. 2-Loosen the 2 oven box attachment nuts on the back of the oven. (loosen only, about 3/8") 3-slide the oven box toward the front of the oven. 4-remove old gasket, and insert new. 5-Retighten 2 oven box attachment nuts. 6-Reinstall door. Took especially long because of incorrect gasket. Deep well socket required to loosen oven box attachment nuts. Recommend two people to do, one in back, for attachment nut and one in front to keep gasket in place while tightning nuts.
Bake Element was bad and Drip bowls needed replaced
First I turned the breaker off the Range. Second I removed the two screws that held the element inplace. Then I pulled element front until I could get to the two screw which connected the wires and removed then. Removed old Bake element. Installed new element by connecting the two wires and then pushed the element into place and secured it by reinstalling the two screws. Turned the breaker back on and tested. This is a very easy item to replace and takes very little time.
Unplugged the range, took old elements out, put new ones in. Couldn't have been easier and for the total cost of about $60; I have a working oven again. A LOT cheaper than a new $600 range!!