JBP24BB4WH General Electric Range - Instructions

watched it on parts select this is a real fast and simple install took longer to pull the range out of its position well started by shuting off the power then double checked that the range was deenergized removed the knob then the 2 screws then on the rear of the range removed the back panel about 8 screws used a nut driver then removed the old switch removed each wire one by one and pluged each wire into the new switch just as they were on the old switch the new switch was exactly the same so every thing matched up perfect installed the screws to the front which hold the swich in place then the back cover turned on the power and tested the switch every thing working ok done shut off power slid range back into its place turned power back on everything still ok

Removed old bake element with a nut drive (two screws) pulled the two wires connected to old element and put them on new element, installed with the two screws and back in business.

I couldn't tell which one work best till I installed 2 units and I liked the other bracket for stability.The wired were too long and there is not a given way to strap them and keep them away from the heat source.

Open oven door, unlock hinges and lift off. Lay on face on carpet or piece of cardboard. Remove 2 screws at top that go thru door and hold handle assembly. Remove 3 screws on bottom that hold bottom door trim to inner door. Carefully turn assembly over (hold it together so you don't drop the glass front!) and place back on floor, hinge side down. Lift off front glass and frame assembly. Lay flat on floor. Remove 4 screws that hold bottom door trim to side frames. If glass is stuck to bottom door trim (which it probably will be from rust and gunk)..... Remove 4 screws that hold side frames to upper handle assembly and completely lift glass and bottom trim out. Holding glass vertical, stand on the bottom trim piece and carfully work the glass up and out of the groove (do not wiggle it side to side or you will need to buy a new piece of glass). While you have everything apart, clean all the parts and remove the decade of gunk. Reassemble in reverse. The long screws at the top of the door that hold the upper handle assembly in place, have spacers around them, they thread onto the screws and maintain distance and alignment when re-assembling. Also, I found it easier to remove the handle from the upper piece (4 screws) to allow me to lay the whole assembly flat while screwing the bottom, side, and upper trim pieces together around the glass front. Once that is done, then put the handle back on before you assemble it to the inner oven door. That is it !

Repair was easy , just removed two screws in lower element. Pulled out a little to unplug the wires. Removed old element. Pluged wires on new element. Installed new element with the two screws. All went well and works well.

I called my dad and he came right over and fixed it. He is a super dad!

Ordered new parts. Received email with tracking number. Parts arrived as promised. Turned off power at breaker (!). Removed burners and pans. Lifted the lid of the range. Inspected the plugs and discovered one had come loose from bracket and was not in straight. Reset plug in bracket. While the lid was open, placed the drip bowl in opening and installed the burner and made sure the burner was laying properly in the drip bowl. Repeat for each. Perfect fit, If done properly, the small burners should lay down flat and not rock back and forth. I have seen complaints about rocking, and experienced some of it on one burner. Make sure the heating element is set in the plug well and it should work. A little patience may be required to get it just right. Everything lays flat and the stove looks new again. I have purchased from Part Select on other projects including a dryer rebuild and a new face plate for this range. Great products, reasonable prices, wonderful tutorial videos and good service.

Pulled range out, disconnected from wall socket. Unscrewed back center cover (3-4 1/4" hex head screws). Removed slide on terminals from lower element. Used multimeter w/continuity checker and found no continuity from tab to tab. (You will get continuity if you touch the outer sleeve). Open the door to oven, remove rack for easy access, unscrew the two 1/4" hex head sheet metal screws holding element in place. Pull element out gently. Slip new back in, securing in place w/screws. Replace rack. Slip on terminals, making sure that they are completely on. Replace back cover. Plug in. Tah dah!

I unplugged the stove and removed the oven racks. Then I turned on a flashlight and laid it in the oven so I could see. Next, I carefully connected the push on terminals. Then I screwed in the two screws with a nut driver. Finally, I replaced the oven racks and plugged in the stove, and I was finished!

two screws two wires two min its to easy

My son took out the burned out bake element and installed the new bake element. Not hard at all. The new element arrived at my home in one day. Thanks.

removed the burners and dropped the drip bowls in. Very easy to do,

unplugged burners replaced drip bowls plugged in burners

1 Turn off power at circuit breaker. 2. Use nut driver to remove the two screws holding element. 3.Remove panel on back off stove to get to the 2 wires that go to unit. The wires will slip right off the element. 4. Remove old element.5.Slide in new element being careful to go through old holes in insulation. 5 P ut the two screws back to hold element. 6. Connett the wire in back to element. 7 Put cover back on. 8. Turn circuit breaker back on. Very easy job.

Removed the racks, used nut driver to remove bolts and pulled old burner out. Pulled connections out of the back of oven wall. Set new burner and connections and replaced screws with nut driver.