JBD2256HEB Jenn-Air Refrigerator - Instructions

took the fridge door off, took off old part that didn't work, replaced with new metal door stop (small part). Perfect-o problem solved with a $5 part! Customer Service here was AWESOME! THANK YOU! WILL SHOP HERE AGAIN.

So cool that you approached me for an update. I noticed that the nipples on the filter head/ receiver were worn down. So I ordered a new filter head/ receiver with hose and installed on my own for like $45. It's working like new now and I am happy I didn't pay $200 for a repairman. It made my wife happy...happy wife = a happy life! Cheers from Santa Cruz, CA.

We re-snapped the new ladder hook into place, which held up the glass shelve over the drawers, and presto.... we had a fix! It took longer to remember how to reassemble the shelf than it did to put the hook into place. :) This was an easy repair.

Temp in fridge stayed around 45-46 degrees even at lowest setting. First went with most probable problem of replacing the Evaporator Motor Kit in lower freezer compartment, no change, next ordered thermistor in fridge area, no change, temp stayed in same range, then tried the Electronic Control Board in top of fridge, fridge works like a charm now. Very easy repair, just follow directions to progam new board. Possible cause a lightning strike near house that fried a TV about 2 years ago - fridge began to freeze items at first and went downhill from there.

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

I merely replaced the cracked piece with the new piece. Presto! Done.

The part came in 5 days from time order. take less then 10 minute done. part work well, have ices again, Thank you Part Select. we don't have to buy a new Rerigerator

I started by changing the water inlet valve. It made one batch but it did not eject into the ben. I removed the ice maker and found that the coating inside was bad. I changed out the ice maker and it is now making lots of ice.

I turned the water supply off and installed the new filter, which was easy. the hard part was finding the water filter at my local home improvement stores; they don't carry it. In the future I will use only Part Select.

Looked at the appliance's booklet to see how it fit together, then installed it.

PartsSelect makes it so easy. I love that they inlcude a picture of each part so I am sure I am buying the right thing!

I went on line and viewed the video. It looked so easy I ordered the new ice maker. Having the information I was able to take apart the old one and view the problem. By the time the new part arrived I was experienced with the installation. I was shocked when the new ice maker arrived within 1 day. I completed the installation without a hitch, I was delighted with the ease of installation and the operation of the new iace maker.Thanks again...Ray

Lift the glass shelf up, slip center rail in place, lower shelf. Time 1 minute.It takes more time to remove everything on the shelf than to replace the part.

went by instructions, used a little common sence.