JB940CB4CC General Electric Range - Instructions

First we confirmed that the part delivered was the correct piece needed. We unscrewed the interior panel of the door and separated the insulation from the two pieces so the old glass frame could be removed. The rope type gasket gave us some trouble as it was difficult to stage the insulation, glass frame and rope at one time. Once we got the pieces in place it was a breeze to screw the panel back in just in time to make pies for our Thanksgiving dinner.

. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two plugs.
plugged in the new element and screwed it in place

It was very easy. First turn off the power. Remove two screws to pick up the hood then remove two screws holding the element. Tag the wires with number. Unplug the old burner attach the wires to new burner. Attach two screws with spring to hold the burner, put the hood down and put the screws holding the top hood.

Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the plug, reinstall the two screws and you are done!

Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!

My cooktop is a stand alone unit mounted in a counter top not associated with an oven.
-Removed power to the cook top. Breaker off.
-Lifted the cook top straight up from the counter top and placed two 24 inch board strips to support it above the counter top. This was very easy by pushing up from the bottom of the cook top. This is a two person job preferably.
-Removed the six phillip screws below the glass surface edge. 3 in the front, three in the back.
-Remove knobs and remove the glass top by lifting straight up.
-Record the wire positions on the element on paper and remove the connections.
-The element is mounted on two spring loaded studs that have spring clips as a retainer. Remove the two clips by pulling straight up with a plier or needlenose.
-The replacement element did not come equipped with the two mounting ears that the original had. I removed the two ears from the defective element and installed them on the new element. Very easy. Two phillips screws. The elements have perferations in the correct areas to accommodate this.
-Placed the new element in position and reinstalled the spring clips.
-Install the wiring terminals in the correct positions.
-Reinstalled the glass surface and the six phillips screws. Reinstall the knobs.
-Lower the cook top back into its counter top position.
-Return power to the cook top.
-Installation complete. Very simple!

very easy remove the bad bulb install the new one

I pulled out the range from the wall unplugged it from the wall then i opened the oven door and removed the two small screws on the front off the range and lifted the glass top and supported it with a 1/2" X 18inc wooden dowel, then i removed the two burner retaining screws with a small Phillips screw driver and removed the wires from the burner,
then i replaced the burner with the new one and reconnected the wires and placed the burner in to the two retaining clips and then tightened the two screws then i removed the wooden dowel and installed the two screws on the front bottom side on the range then i plugged in the range in and tested the burner then put the range back against the wall.

Took off cover plate and removed screws from housing to switch. Connected each wire from old switch to new one. No problems.

I went online and ordered the part after reading other people's repair experiences, confident that I could do it because the part was quite pricey. First, be sure you're circuit breaker to your range is off. Next, open the oven door and locate and remove two screws with a socket, that are just under the top surface which will allow you to lift up the glass top which is actually hinged...no need to pull the range out. Securely prop up the glass surface area and the burners are exposed. With a marker, mark where each color wire goes on the burner you are going to remove and also mark where the two holding brackets are. This way you can reference the locations to connect to the new one. Carefully remove the wires and brackets and install new burner with brackets and connections. Close up the top, replace two screws, turn on breaker, and if there were no other faulty components,it'll work great. P.S Be gentle getting the very snug wires off. Good Luck

replaced lights in refrigirator and freezer

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!

1.) I removed the old oven door gasket by taking out the ends of the gasket out of the bottom of the oven door first.
2.) Pry up on each one of the retainer clips, they easily pop out of their slots.
3.) Work your way around the oven door gasket.
4.) If any remain stuck you can just wiggle the clip around and it should pop out of each hole. If need be you could use pliers, but I did not need to.
5.) Take your new gasket, it should already have new clips, so you can throw away the old ones.
6.) Work your way around the oven door making sure the clips are nicely seated.
7.) Finish off by inserting the ends back into the 2 holes on each side of the bottom of the oven door, I just used a small spoon to make sure the tops were nicely placed in.
8.) If your gasket needs to compress, you can close the oven door and lock it that should hold it in place and compress it.
9.) All done!

It took a bit of head scratching to remove the oven door. I had read another user saying he'd removed the hinge screws unneccessarily, so I left them alone. I eventually was able to locate the locks on each hinge. Once they were disengaged, it was a simple matter to lift off the door. After that, I removed all the screws (except the hinge screws) and took the door apart. Once it was disassembled, I found two loose triangular pieces, about 1 1/2" long. I later discovered these were spacers for the two top srews. They were placed on end, and the top screws passed through them. All in all, a relatively simple repair, which absolutely amazed my wife, landlord, faily, etc.

Removed the two screws that hold the range top down. Lifted up yhe range top and propped with a stick. Proceeded to mark the wires connected to the old burner so that the new one would be connected correctly. Removed the wires and then the two brackets that hold the burner in place. Removed the old burner and installed the new one. Connected the wires and resecured top to base. Turned on the current and it worked beautifully.

Very simple repair. Remove two screws to lift the range top. Then remove the two screws holding the element in place. Disconnect the wires from the old element, connect the wires to the new element. Reverse the procedure and you are done. Total time is anywhere from 15 to 30 minutes.