JB900WD1WW General Electric Range - Instructions

Step 1. Turn off the breaker to the range. Step 2. Pull the range out from the wall. Many of the installation instructions recommend accessing the element from the front only and to use clips to keep the wires from popping back into the insulation. My recommendation is to just pull the range out and take off the back cover. This is much easier than worrying about losing the wires. The connectors will be easy to access from the rear. You know you need to clean behind your range anyways. Step 3. Remove the back cover of the range. Step 4. Disconnect the two wires that are attached to the lower element. Step 5. From inside the oven remove the two screws holding the element and remove the element. Step 6. Insert the new element and reinstall the two screws to secure it. Step 7. From the back of the range reconnect the two wires to the element. Step 8. Reinstall the back cover. Step 9. Turn the breaker back on. Step 10. Test the new element.

In order to replace the bottom trim (and side trims if needed) it is necessary to separate the oven door front panel and its outer glass from the inside door panel. It is best to remove the entire oven door and lay it down on a table in order to do this. (Refer to owner's manual for instructions on removing the door from the oven, but it basically lifts out easily when is is in the broil-open position). Remove the front panel of the oven door by unscrewing the two machine screws (these may be torx head screws on your appliance) on the top inside corners of the door that hold the door handle. (screw spacers on the inside likely will fall out when you remove the machine screws - don't be alarmed) Then remove the three screws at the bottom of door trim. The front panel can then be lifted away from the back panel. This will allow access to the screws that hold the bottom trim to the side trim. Remove these and the bottom trim will slide off. Replace trim pieces and reassemble.

Took two nuts loose disconnect electric connect new element reinstall screws

Disconnect the range from the mains. Open the door. Remove the single screw holding the temperature sensor - this is located on the back wall on center and is screwed to the broiler mounting plate. Remove the four screws holding the boiler element and allow it to hang down on the wire; this exposes a space to feed the wire through later. Now move to the back of the range and remove the six screws that hold the central cover plate. Now push the insulation to up out of the way and you can disconnect the temperature sensor, pull it out through front, insert the new one and connect it. Reassemble in the reverse order. Mine worked perfectly!

Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.

Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw

I found that installing my element was far easier when I found this link it is a video on how to install this part It made it far easier to install correctly.

turned power off, loosing the to screws, left up and pull front, removed the two connection.placed new element inside oven fsten the two wires. push elemen, back in place, allaing screw holes tighten screw, turn power back on. Stove(oveb) working just like new.

We pulled the stove out, unplugged it, unscrewed the old element and screwed the new one in.

pull gasket from door bottom and pull gasket to release retainers in door frame. refit new seal in retainer holes and push gasket into slots at bottom of door. done perfect fit.

Extremely easy, two screws pull connection inward to oven grasp push pin pull disconnect (don't let go of oven end or it will recede into appliance) push pin new connection on two connections. Remount with two screws and job was done! And yes a woman repaired her own oven very easy!

Instruction were very easy to follow.

Like the others, the element is easy to remove. Just 2 bolts. However, the wires attached to the element are very short on this appliance and if not extremely careful, they will pop back into the insulation. I was half careful as only 1 popped back. I secured the 1 wire with a small clamp and removed the central panel in the back of the range (5 bolts). I worked the wire back into the oven, attached both to the element, attached the element to the back of the oven, neatened the insulation in the back, and replaced the center panel. It wasn't difficult.

Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.

I ordered it online and it came to our house in less than 24 hours which is very impressive since we live in a very remote place. There were responses from other people who had the same problem and what they had to do to fix it which was very helpful because we knew what might happen. The wires went into the back of the oven when the old element was removed. We were ready, opened up the back of the oven and stuck it back in, connected it, cleaned behind the oven while it was out, put it back, and it works like new. Thankyou so much!