JB660SM1SS General Electric Range - Instructions

I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .

I found a video on Youtube with a similar circuit board repair and decided that I could probably do it. First and most important is to be certain the range is disconnected from its electric circuit. I did this by turning off the breaker at the electrical panel and then unplugging the range. Second, I removed a panel (four screws) on the back of my stove to expose the circuit board, Next I removed the board (four screws) without disconnecting the wiring. Then I removed the flexible plastic covering from the board which has the control button identities on it. This was the most difficult part because the glue was very sticky and I did not want to tear the cover. After removal, I stuck the plastic covering (still sticky) onto the new circuit board and made sure the buttons were in the correct position. Then, I unplugged the wires one at a time from the old circuit board and made sure I plugged them into the new board in the correct position. Finally, I reattached the new board and the back panel on the stove. This repair was easy and no problem for the average "do it yourself" type.

Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.

Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw

Purchased the board installed it and saved about 130 dollars.

We've had this range for almost 10 yrs and while on the clean cycle the bake element burned up. We ordered the new bake element on Wednesday and was delivered on Friday. Installation was not difficult as we followed the advice of other installation reviews. However, while removing the old element one of the wires snapped back into the insulation. We had to remove the back cover plate and found the correct wire and just pushed it through. Easy, peasy, japaneasy!

There were no burnt spots on the baking element but I turned the electric power off and removed two screws and removed the two termenals wires and replace them on the new element and replaced the two screws that I removed. I turned the electric back on. Every thing is great and it only took me fifteen minute from start to finish.THANK'S

unscrew element, remove back panel of range. replaced element and reattach connectors. reistall back

followed instructions from the order information sheet.

I miss diagnosed the situation at first. When the top element only heated up I thought the control was the problem. Wrong. Apparently both elements heat up during initial start up. It turned out that the bottom element was not working so it needed to be replaced rather then the control. Now both are replaced and the oven is now back to original status. Entire repair cost about $80. I saved over $100 by attempting this myself. Easy fix. Obviously I am not a pro. My local hardware store had a generic heating element that worked just fine and only cost $22. Two screws to repair after removing the back panel. Remember to pull the plug before you begin and after the repair put all panels back on before plugging back in. Pizza anyone?

I found that installing my element was far easier when I found this link it is a video on how to install this part It made it far easier to install correctly.

turned power off, loosing the to screws, left up and pull front, removed the two connection.placed new element inside oven fsten the two wires. push elemen, back in place, allaing screw holes tighten screw, turn power back on. Stove(oveb) working just like new.

Took door apart to clean inside of glass door. scraped most of the wax from the stove 99%. Could not get the last 1%. Cleaned all parts. Put door back together again, put the door seal on after I got the right one. Had to reorder a new seal(one that was actually made for that model) messed up the first one and whalla! Took about 3 weeks to clean off the wax from stove and the surrounding area. Stove is good as new. Thanks for the quick service. Would definitely recommend and use you guys again. Thank You.

replaced insulation

My husband took care if it, very simple...took him less than 10 mins.