Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old Burners Fade Away
I removed the screw holding the tilt-lock hinge, then removed the insulator brackets and unscrewed the wire terminals. Units come with new insulators, brackets, terminal screws & hinge screw. This is a very straightforward operation.
Trim Ring - 8" didn't fit right and Drip Bowls were not cleanable any more
Replaced all the ordered parts, and straightened a bent "rest piece" (one of three) on the element os the large burner, which made it rest perfectly on the new Trim Ring. It doesn't easily fall down into the bowl now while I am using the burner. The new Bowls look so nice, and the stove looks nearly new!
I now know where to go for help when I need to repair appliances. You seem to have everything that could possibly be needed. Thank you!
New one a little different ,but it was marked for wiring! Had to install upside down because wires would not reach right side up! Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up! Works fine! Now all burners work again!
Simple repair that was complicated by not being able to remove the oven door, leaving a long reach to the element connections in the back of the oven. Other than the accessibility issue, the repair is easy. Remove two scews, pull the element out about 3 inches to access and unscrew the screws holding the wires to the element. Then reverse the process with the new element. But, because of the long reach, there were alot of dropped screws and cussing.
First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.
I removed the screw holding the tilt mechanism to the range top. Removed the clips holding the block together. Disconnected the two power leads on the old burner and replaced with the new burner. Closed the block around the leads. Screwed the tilt mechanism back to the range top and that was it!
Old infinite switch WB21X36771 broke...heating element stopped heating
1. Bought replacement part said to replace old switch. 2. Pulled old switch out. 3. Replacement part did not match. Would have to take entire switch panel apart to change to this part. 4. Multiple-part instructions very poor. For my switch unreadable. 5. Old part was "push to turn". New part was not. 6. Knob did not fit new switch. Old shaft was "D" shaped. New is square. 7. Gave up. Need to call repair shop. 8. Hope this helps.
First removed oven door, according to Reader's Digest repair manual, then removed two screws holding element. Pulled element out several inches, then removed one side of bracket holding up front of element so that bad element could be pulled further out. Then disconnected two red wires from one side and two light blue wires from other side. Removed old Element. Attached two light blue wires to one side and two red wires to other pole, inserted element back into rear wall and attached with two screws, Re-attached bracket holding up front of element. Re-installed door. Tested and it worked fine.
burner would not lay flat against surface of range.
Removed two clips that held the ceramic insulators in place. Removed two screws that held conductors to the burner. Replaced screws onto new burner unit, replaced ceramic insulators. Fastened clip to burner onto the range. Turned burner on and it worked great. Thank you for your quick responce to my order.
Lifted burner element to remove pressure on ring and drip bowl. Removed old parts and replaced in reverse order. This not intended to sound sexist, but my wife who is not particularily mechanically inclined performed the task on her own.
Just pushed the new timer knobs onto the stem. They fit and now I can set the oven timer without having to use a pair of pliers to grip the stem and turn it.
Two of the knobs fit perfectly.
The stem for the the clock was broken off and there was not enough of the stem left for the new knob to fit.
Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory. Knott County Housing Authority Maintenance Personnel
Broiler element arrived at my door 3 days after ordering which was nice. Apparently the billing dept. is out of the USA so don't be surprised, like I was, to find a suspicious looking charge for a currency exchange fee (mine was 42 cents). I had to drill two new screw holes in the base of the new element in order for it to fit my oven. I also had to use heavy wire snips to cut off about an inch of the top of the new element base. The female electrical connections also had to be spread out with needle nose pliers since the new element connections were slightly thicker. With all of the issues I had I was frustrated and it took about two hours. On the other hand, the part works perfectly and was priced right. Hopefully it will fit perfectly out of the box for your oven.