HED4400TQ0 Magic Chef Dryer - Instructions

Diagnose the problem. Is it the motor ? Is it the belt ? Order the correct repair kit, use name brand parts to ensure reliability. READ THE SUPPLIED DIRECTIONS. You can use a small wood shim or wedge at the top front corners to open the top . Use a 5/16" socket to remove the 2 screws at the top outside corners. Lift the front panel straight up, supporting the drum as you lift it off. Remove the drum, taking it straight out the front. Install the new drum rollers, install the idler, and then the belt around the drum. Install the drum on the rear rollers, make sure the seal is not folded under. Push the drum back against the seal flange, support the front of the drum with your right (or left ) hand, and sit the front panel on the lower pins, and gently push the front panel to the sidewalls. Feed the belt through the idler and around the motor pulley. This job is easily performed in about 20 minutes. Clean the interior while replacing the belt/idler and drum rollers. With the top lifted, after assembly, test run the dryer to make sure there are no "funny noises" after the repair. Watch especially for the white rub strips on the front edge of the drum. They tend to fold over when attaching the front panel. Job done !

I replaced the Thermal fuse and this fixed the problem.

My husband unscrewed the plate in the back of the dryer, removed the heating element and placed the new element in! Dryer works like new!

1) Watch YouTube video on this site showing the steps to replace the heating element. 2) Assembled the proper sized screw driver, pliers and nut driver. 3) Unplugged the dryer and pulled it away from the wall. 4) Disconnected the vent hose by using the screw driver to loosen the clamp securing it to the dryer. 5) Removed the back panel by removing the hex head nuts / screws. 6) Unplugged the thermostat and wire to heating element terminal using the pliers. 7) Removed the panel concealing the heating element and removed the heating element. 8) Replaced the bad element with the new one purchased from PartSelect and replaced the heat shield panel. 9) Re-attached the thermostat and reconnected the power terminal. 10) Replaced the back panel with the hex head nuts / screws. 11) Reconnected the vent hose and tightened the clamp with the crew driver. 12) Repositioned the dryer back to it's original location, careful not to pinch the vent hose and plugged the unit back in. 13) Ran the unit with some old towels to test. 14) Unit was fixed and works like new.

Ordered your fuse & thermostat. Total $37.29, installed parts & still no heat. Ordered your 240v Heating element.. Total $77.43, installed part & still no heat, Removed 30amp circuit breaker and purchased replacement for $11.30 in town. Installed breaker, dryer now has heat. Still smiling as I keep telling my self I performed preventive maintenance on my dryer!!!

I followed the video directions exactly as instructed and I had no problem doing the repair myself. And if I can do it being a woman with no help you can do it. Easy peasy~

unpluged dryer from wall,lifted top of dryer unpluged door switch took out two screws that hold switch, installeed new switch, put top of dryer down, plugged dryer back into wall, very easy repair.

1.Installed thermal fuse. I thought this was the problem as a few years ago this fixed the dryer that was now experiencing a similar problem. Problem persisted. 2. Installed new thermostat. Problem persisted. 3. Installed new igniter coils. Eureka! Problem solved!

Watched repair video first to access problems and steps to do replacement for parts. Took more than :30 only because most of the time was spent cleaning. Amazing how much dirt and dust accumlates inside a closed unit. Even took the back off to clean and check electrical connections. Parts were exactly as shown and explained. Would absolutely use PartSelect again if needed.

I simply pulled the dryer away from wall. Cleaned vents. Pulled plug out from outlet. Unscrewed the back panel and removed the cycling thermostat and fuse as per your instructions. Since I had the back panel removed I cleaned the inside of lint as well. Put the back panel back started the dryer and everything was perfect. Saved myself at least 150.00.

I ordered the part I suspected....which was indicated by approximately 44% of the users having success replacing the thermal fuse. After watching the video on how to perform the repair, it was a snap! Removed the 9 screws, removed the vent hose, popped out the fuse, and replaced it. After checking to see if that was the problem....which it was, I reassembled the dryer. It only took more time because I chose to vacuum any exposed areas. THANK YOU!

Verified that the heater element was working; drum and contents were getting hot. Could hear the thermostat clicking on/off as the element started to glow. Drum stayed very steamy the entire time; consistent with no airflow. Fan motor was running, dryer vent/line were clear. Verified cold (not hot) air from the external vent. Seals had degraded to the point that the fan was not drawing air from the drum, but from inside the dryer cabinet at the lower seal (by the fan blades); hot air was escaping from the upper seal and was causing the dryer cabinet to get unusually hot. Installed these 2 seals, and the dryer is working perfectly now.

TURN OFF POWER TO DRYER............................. Pay attention to where everything is as you take it apart, so it can be put back the same way. Take out the two screws by the lint screen. Use flat tip screwdriver between space in front of top to help lift top. Use rag on tip of screwdriver so as not to scratch it. Take out two screws inside the front panel at the top. One on each side. Unhook the switch wiring. Lift up the front panel to take off. The tub will be loose, so it can be taken out to inspect other components. Some call the tub a drum. Be sure to see how the belt tensioner is attached, so it can be put back on the same way, if it comes loose. It is under the tub. Take out old belt. Put new belt around tub. Make sure the tub sets on the two rollers in the back of dryer. While holding tub, put the belt around the grooved pulley on the motor. Grooves are face down against the tub. Feed belt through the tensioner. Put the bottom of front in on the tabs. Be sure belt is still in place around pulley and tensioner etc. Hold tub through front door and close front. Put the two screws back in on each side. Close top and put the two screws in at the lint screen. Done. Turn power back on. Turn on dryer to see if it operates properly. If not, check out your repair to see if everything is connected properly.

The repair was very easy. It just didn't fix my problem.

Removed rear panel and visually observed coil on heating element was broken. Ordered element and replaced. Works great!