Enter the code TAKE10OFF at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on May 28 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ice stripper broken on ice maker
I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!
From the beginning I have never had good water flow in the door and ice cubes turned out funky. I tried replacing the filter once with hardly noticeable change. The change I did see was $35 less in my pocket. So I bought a filter bypass plug and it now works like a champ. I have well water so I trust its quality and I am very satisfied. I would describe how I did the repair but if you don't no how to change out the filter you probably shouldn't be trying it.
I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.
I removed all contents from the lower shelf. I, then removed both of the pull out drawers. Secondly, I removed the lower glass shelf and the glass support tray. At this point all four plastic shelf supports were accessible. I removed the inner screw from all four supports and replaced with four new shelf supports. Then reassembled in reverse order. Very easy to do!
first i remove the two screws like the guy said on your web site. then i pulled the cover off with a upward motion revealing three more screws witch i removed. I then removed the dispencer. unpluged the wires and removed the switch and pad and replaced with new parts.I reinstalled the wires then the unit, installed the screws and cover.Checked for proper operation.Then enjoyed that cold beer! Thanks to your wed site and repair info. I saved at least 100 buck to the repair man. Thanks Partselect.com
Ice door plastic wing on one side broke off, keeping ice shut open.
I first removed the tray at the bottom of the Ice/water compartment, 2nd, removed the 2 star headed screws that are visible and 1 star screw near the water hose. removed front pannel. 3rd removed 4 star screws holding ice/water assembly, let this hang down and was able to reach in and removed the round broken shut door. replaced with new door, Difficult to get new door in but I was lucky and got both side wings in the proper slots. Did everything from above in reverse. New Ice doot works great. I just wish you had sent some type of instructions! Very happy with your company. Other web sites wanted me to buy a complete kit just to get the door assembly. you saved me $30. Thanks
I had to cut off the old yoke since the threads had stripped and it would not come off. Once I did that all I had to do was to remove 4 screws on the auger motor and replace it with the new auger motor. Then I put the yoke on the new auger motor shaft and then put the unit back in the freezer. Work time was less than 15 minutes with no problems.
First I removed the spill tray, and removed the two screws on the bottom of the dispenser. I was then able to remove the front of the dispenser, which revealed 3 more screws. After removing those screws, the entire assembly lifts out. I removed the old pad, put the replacement pad on, replaced all the screws and the tray, and was done! It took about 10 minutes, start to finish. I saved at least $75 on the repair by doing it myself, and the part only took 3 days to arrive. Best of all, the water and ice dispenser works like new! Thanks, PartSelect!
This was not a difficult project at all. I removed the ice bin and then unplugged the wiring hareness. With the old enclosure removed I first removed all of the screws holding the solenoid (look at the way it is mounted before removing all screws). I then removed the drive motor for the ice crusher/dispenser. The yoke on the drive motor has a left hand thread. Grip the motor shaft behind the yoke with a thin pair of channel locks or pliers and tap on the yoke in a counterclockwise direction with a small hammer to loosen and remove the yoke. I then reattached the motor and reinstalled the yoke and then reinstalled the solenoid. It was a bit of a trick to plug in the wiring harness, but if you use a small mirror you can do it with ease. Be sure and align the drive motor yoke with the couple on the ice bin at a 90 degrees from the yoke on the motor. Also make sure the dispensing mechanisim on the ice bin moves freely. If not remove all ice from the bin and locate where the ice is jammed and remove it. Trust me this will save the new enclosure you just installed.
I Removed the two wires from the old relay. I Then pulled the old relay off the compressor. Next, I had to get the overload seperated from the old burnt relay, which took some care not to break. The old relay and overload is in a plastic compartment. Then I followed the directions that came with the new relay. The only confusion came with getting the two wires back onto the terminals of the new relay, mainly because the old relay was burnt so badly I didn't have any idea how it was originally wired. I crossed the two wires on the terminals of the relay. The compressor would click off and on, but would not start blowing cold air. I swapped the wires on the terminals and it started working immediately.
Light switch rocker broke, disabling freezer internal light, water dispenser, and ice dispenser
Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.
Step 1 :I had to remove the ice drip tray just pull it out. Step 2 remove the 4 or 5 screws holidung in the control module (push button display pad) step 3: pull the plug from the diaplay panel Step 4: remove broken door from slot and slide new one in. Be carfull not to let the brass plug fall out of it does it just slides back in. Reverse all steps your done about 20- minutes..I am a building engineer by trade. I think the average person 30 to 60 minutes..
Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiver boaed. I turn off manually the icemaker, when needed
removed the ice chute door, unhooked the computer board replaced the flap. The only problem was the spring loaded part of the ice chute door come up and the little plunger came loose. It only took a few minutes to replace the plunger back in the holder and replaced the ice chute door. The best part of the whole job was that I ordered the part on Monday afternoon and the part was at my door Wednesday. The Parts did an excellent job of getting the part to me quickly.