Models > GZ2727GEHB > Instructions

GZ2727GEHB Maytag Refrigerator - Instructions

All Instructions for the GZ2727GEHB
181 - 191 of 191
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
the ice enclosure broke, it will not dispence ice.
I followed the instructions of the users of this page. It was very easy easy job, saved about $75- $100 on labor.
Parts Used:
Ice Enclosure
  • David J from Brownwood, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Loose hinge cover
Replaced by snapping in new part
Parts Used:
Freezer Lower Hinge Cover
  • Ron from San Antonio, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broken ice bin drive ring
Easy disassemble removing screws to separate front of ice bin.Be sure to note how metal rod is attached to rear of ice bin. Installed drive ring and reattached face (front) of ice bin in about 15 minutes.
Parts Used:
Ice Bin Drive Ring
  • James from Lincoln, NE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
broken fan blade
unplug refrigerator, take backing off with nut driver. Pull old blade off and put new blade on. Put backing back on and plug in.
Parts Used:
Fan Blade
  • David from Ceres, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Frost in bottom freezer, freezer 8%, ice maker works
replaced electric control board, defrost for six hours. next day (24 hours) same problem, dusterhoff2928@charter.net
Parts Used:
Door Switch
  • Richard from Smyrna, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
Compressor would not run.
Replacement parts looked different than the originals, however with the on-line feedback from similar customers and a well worded OM, the repair was quick and simple. Thanks to all.
Parts Used:
Relay and Overload Kit
  • Chad from Lexington, KY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Water Dispenser didn't shut off immediately when glass was no longer pressed against actuator pad
We followed the directions in the video on the Parts Select website.My husband thought it was so easy and he isn't handy. I agree.
Parts Used:
Ice and Water Dispenser Actuator Pad
  • Sharon from Sugar Grove, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
My refrigerator light did not work.
After years of using a flash light to check the contents of my refrigerator, I decided to try to fix the problem myself. Replacing the light switch was very easy. The directions were straight forward and I'm sorry I waited so long to tackle the problem.
Parts Used:
Door Switch
  • Fred from Warwick, RI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The original ice eclosure broke
Turn off the appliance. There is a screw under the left side that must be removed. Then you will need to kind of push back and lift up on the old enclosure to remove. Once free, reach back on the left side and uncouple the wiring harness. You will need to squeeze in the top and bottom to free it. The hardest part was removing the ubolt off of the motor. I used my vice and a pair of waterpump pliers. Remember the threads are counter clockwise. Then it is just a matter of installing the old parts on the new enclosure and sliding it back in place. You will need to remove the water from the ice maker to get it to start again. Rather than removing it it pour the water out, I just soaked it up with a sponge.
Parts Used:
Ice Enclosure
  • Mike from Ft. Collins, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
freezer normally functioning, refrigirator side too warm
I watched the instructional video included with the shipping date e-mail(about 3 minutes long), and simply followed the instructions. It took about 2 days for the refrigirator section to return to normal cool temperature to the level set.
Parts Used:
Air Return Cover
  • Joseph from Hamburg, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ordered ejector arm.
No instructions with part. Found a picture on line and changed the arm, but it didn't fix the problem. Fairly easy after figured out what needed to be done to get to the part.
Parts Used:
Ejector Arm
  • Joyce from Springfield, MO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GZ2727GEHB
181 - 191 of 191
Back to Top